Hot deformation behaviour and fracture of 10CrMoWNb ferritic-martensitic steel

被引：40
|
作者：
Churyumov, A. Yu. [1 ]
Khomutov, M. G. [1 ]
Solonin, A. N. [1 ]
Pozdniakov, A. V. [1 ]
Churyumova, T. A. [2 ]
Minyaylo, B. F. [2 ]
机构：
[1] Natl Univ Sci & Technol MISiS, Moscow 119049, Russia
[2] JSC VNIINM, Moscow 123098, Russia
来源：
MATERIALS & DESIGN | 2015年 / 74卷
关键词：
Ferritic-martensitic steel; Hot deformation; Constitutive model; Structure; Fracture; TEMPERATURE FLOW-STRESS; STAINLESS-STEEL; FERRITIC/MARTENSITIC STEELS; CONSTITUTIVE ANALYSIS; ALUMINUM-ALLOY; MICROSTRUCTURAL EVOLUTION; RESISTANT STEEL; COMPRESSION; PREDICT; WORKABILITY;
D O I：
10.1016/j.matdes.2015.02.023
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
High-Cr ferritic-martensitic steels are important materials for use in nuclear reactors. This study describes a development activity for this category of steels involving the investigation of the hot deformation behaviour and microstructure evolution during hot deformation of 10CrMoWNb steel. Hot compression and tension tests were performed in the temperature range of 900-1350 degrees C by using a Gleeble 3800 thermomechanical simulator. The results indicate that the flow stress and ultimate tensile strength increase with a decrease of the deformation temperature and an increase of the strain rate. Based on the experimental true strain-true stress data, the modified Arrhenius-type constitutive model was established for a form of 10CrMoWNb ferritic-martensitic steel. The hot plasticity properties of the 10CrMoWNb steel increase with temperature up to 1275 degrees C due to dynamic recrystallisation processes in the austenite phase. The reduction of area decreases when the temperature is higher than 1300 degrees C and is zero at 1350 degrees C for all strain rates because of the liquid phase appearance in the structure of the steel. (c) 2015 Elsevier Ltd. All rights reserved.
引用
收藏
页码：44 / 54
页数：11
相关论文
共 50 条
  • [21] New ferritic-martensitic stainless steel constitution diagram
    Welding and Joining Metallurgy Group, Ohio State University, Columbus, OH, United States
    Welding Journal (Miami, Fla), 2000, 79 (12):
  • [22] Microstructural Deformation and Fracture of Reduced Activation Ferritic-Martensitic Steel EK-181 under Different Heat Treatment Conditions
    Polekhina, N. A.
    Litovchenko, I. Yu.
    Akkuzin, S. A.
    Spiridonova, K. V.
    Osipova, V. V.
    Chernov, V. M.
    Leontyeva-Smirnova, M. V.
    PHYSICAL MESOMECHANICS, 2024, 27 (05) : 529 - 540
  • [23] Grain Boundary Engineering of 10% Cr Ferritic-Martensitic Steel SUH3
    Hirayama, Kyosuke
    Yoshi, Yonosuke
    Morizono, Yasuhiro
    Tsurekawa, Sadahiro
    Hidaka, Yasuyosi
    ISIJ INTERNATIONAL, 2015, 55 (09) : 1973 - 1979
  • [24] EFFECT OF SEVERE PLASTIC DEFORMATION ON RADIATION HARDENING OF T91 FERRITIC-MARTENSITIC STEEL
    Voyevodin, V. N.
    Tolstolutskaya, G. D.
    Karpov, S. A.
    Velikodnyi, A. N.
    Tikhonovsky, M. A.
    Kalchenko, A. S.
    Tolmachova, G. N.
    Vasilenko, R. L.
    Kopanets, I. E.
    PROBLEMS OF ATOMIC SCIENCE AND TECHNOLOGY, 2021, (02): : 35 - 42
  • [25] Effects of Tungsten and Tantalum on Creep Deformation and Rupture Properties of Reduced Activation Ferritic-Martensitic Steel
    Vanaja, J.
    Laha, K.
    Mathew, M. D.
    Jayakumar, T.
    Kumar, E. Rajendra
    6TH INTERNATIONAL CONFERENCE ON CREEP, FATIGUE AND CREEP-FATIGUE INTERACTION, 2013, 55 : 271 - 276
  • [26] A combined experimental-numerical investigation of ductile fracture in bending of a class of ferritic-martensitic steel
    Soyarslan, C.
    Gharbi, M. Malekipour
    Tekkaya, A. E.
    INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES, 2012, 49 (13) : 1608 - 1626
  • [27] Assessment of Tungsten Content on Tertiary Creep Deformation Behavior of Reduced Activation Ferritic-Martensitic Steel
    Vanaja, J.
    Laha, Kinkar
    METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2015, 46A (10): : 4669 - 4679
  • [28] Behaviour of ferritic-martensitic steel and aluminium base coatings under demanding elevated temperature conditions
    Huttunen-Saarivirta, E.
    Metsajoki, J.
    Kuokkala, V. -T.
    TRIBOLOGY-MATERIALS SURFACES & INTERFACES, 2014, 8 (02) : 57 - 64
  • [29] INFLUENCE OF MARTENSITE MORPHOLOGY ON DEFORMATION CHARACTERISTICS OF FERRITIC-MARTENSITIC STEELS
    RAU, RHG
    GUPTE, KA
    ACTA STEREOLOGICA, VOL 6, SUPP 3, PARTS 1-2, 1987, 6 : 479 - 483
  • [30] Thermomechanical Fatigue Behaviour of a Modified 9Cr-1Mo Ferritic-martensitic Steel
    Nagesha, A.
    Kannan, R.
    Sandhya, R.
    Sastry, G. V. S.
    Mathew, M. D.
    Rao, K. Bhanu Sankara
    Singh, Vakil
    6TH INTERNATIONAL CONFERENCE ON CREEP, FATIGUE AND CREEP-FATIGUE INTERACTION, 2013, 55 : 199 - 203
12345