Surface Quality Experimental Study on Rotary Ultrasonic Machining of Honeycomb Composites with a Circular Knife Cutting Tool

被引:10
|
作者
Liu, Gang [1 ]
Yang, Jie [1 ]
Zhang, Liqiang [1 ]
Gao, Qiuge [1 ]
Qian, Long [1 ]
Zhang, Rongyao [1 ]
机构
[1] Shanghai Univ Engn Sci, Sch Mech & Automot Engn, Shanghai 201620, Peoples R China
基金
中国国家自然科学基金;
关键词
Nomex honeycomb composites (NHCs); aluminum honeycomb composites (ALHCs); rotary ultrasonic machining (RUM) technology; surface quality; cutting parameters; SANDWICH PANELS; BEHAVIOR;
D O I
10.3390/cryst12050725
中图分类号
O7 [晶体学];
学科分类号
0702 ; 070205 ; 0703 ; 080501 ;
摘要
Honeycomb composites (HCs) are diversely employed in aerospace, national defense and other fields owing to their remarkable spatial geometry and excellent mechanical properties. Their complex hexagonal cell structure and heterogeneous material properties cause major problems when implementing high-quality processing. Surface defects generated by processing will reduce the capability and service lifespan of the honeycomb sandwich structure. Therefore, the high quality of HCs is a topic of close attention for researchers. In this paper, the consequences of different cutting parameters of rotary ultrasonic machining (RUM) on surface quality with an ultrasonic circular knife (UCK) were studied through multiple groups of single-factor and orthogonal experiments with two-factors/four-levels and one-factor/three-levels. The single factor experiment was used to explain the effect that the degree of cutting parameters has on surface quality, and the orthogonal experiments were applied to explain the interaction between the processing parameters and the influence law of each factor on surface quality. Therefore, the reasonable cutting parameters of HCs were determined through experimental results to provide guidance for the realization of the precise and efficient machining of HCs. This study can provide a basis for the subsequent comprehensive consideration of various factors to achieve high-quality machining of HCs.
引用
收藏
页数:18
相关论文
共 50 条
  • [21] Experimental Investigation of Tool Wear in Rotary Ultrasonic Machining of Alumina
    Zeng, Weiming
    Xu, Xipeng
    Pei, Zhijian
    ADVANCES IN GRINDING AND ABRASIVE TECHNOLOGY XV, 2009, 416 : 182 - +
  • [22] DELAMINATION IN SURFACE MACHINING OF CFRP COMPOSITES USING ROTARY ULTRASONIC MACHINING WITH HORIZONTAL ULTRASONIC VIBRATION
    Wang, Hui
    Zhang, Dongzhe
    Li, Yunze
    Cong, Weilong
    Burks, Anthony R.
    PROCEEDINGS OF THE ASME 2020 15TH INTERNATIONAL MANUFACTURING SCIENCE AND ENGINEERING CONFERENCE (MSEC2020), VOL 2A, 2020,
  • [23] The effects of elliptical ultrasonic vibration in surface machining of CFRP composites using rotary ultrasonic machining
    Wang, Hui
    Zhang, Dongzhe
    Li, Yunze
    Cong, Weilong
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2020, 106 (11-12): : 5527 - 5538
  • [24] The effects of elliptical ultrasonic vibration in surface machining of CFRP composites using rotary ultrasonic machining
    Hui Wang
    Dongzhe Zhang
    Yunze Li
    Weilong Cong
    The International Journal of Advanced Manufacturing Technology, 2020, 106 : 5527 - 5538
  • [25] Rotary ultrasonic surface machining of CFRP composites: Effects of horizontal ultrasonic vibration
    Wang, Hui
    Hu, Yingbin
    Cong, Weilong
    Burks, Anthony R.
    47TH SME NORTH AMERICAN MANUFACTURING RESEARCH CONFERENCE (NAMRC 47), 2019, 34 : 399 - 407
  • [26] Rotary Ultrasonic Surface Machining of CFRP Composites: A Comparison with Conventional Surface Grinding
    Ning, Fuda
    Wang, Hui
    Hu, Yingbin
    Cong, Weilong
    Zhang, Meng
    Li, Yuzhou
    45TH SME NORTH AMERICAN MANUFACTURING RESEARCH CONFERENCE (NAMRC 45), 2017, 10 : 557 - 567
  • [27] Enhancing the Machining Performance of Nomex Honeycomb Composites Using Rotary Ultrasonic Machining: A Finite Element Analysis Approach
    Zarrouk, Tarik
    Salhi, Jamal-Eddine
    Nouari, Mohammed
    Bouali, Abdelilah
    MATERIALS, 2024, 17 (09)
  • [28] Experimental investigation of tool wear and machining rate in rotary ultrasonic machining of nickel alloy
    Popli, Dipesh
    Gupta, Meenu
    MACHINING SCIENCE AND TECHNOLOGY, 2018, 22 (03) : 427 - 453
  • [29] An experimental study on rotary ultrasonic machining of Macor ceramic
    Singh, Ravi Pratap
    Singhal, Sandeep
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE, 2018, 232 (07) : 1221 - 1234
  • [30] Experimental observation of tool wear in rotary ultrasonic machining of advanced ceramics
    Zeng, WM
    Li, ZC
    Pei, ZJ
    Treadwell, C
    INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2005, 45 (12-13): : 1468 - 1473