Surface Quality Experimental Study on Rotary Ultrasonic Machining of Honeycomb Composites with a Circular Knife Cutting Tool

被引:10
|
作者
Liu, Gang [1 ]
Yang, Jie [1 ]
Zhang, Liqiang [1 ]
Gao, Qiuge [1 ]
Qian, Long [1 ]
Zhang, Rongyao [1 ]
机构
[1] Shanghai Univ Engn Sci, Sch Mech & Automot Engn, Shanghai 201620, Peoples R China
基金
中国国家自然科学基金;
关键词
Nomex honeycomb composites (NHCs); aluminum honeycomb composites (ALHCs); rotary ultrasonic machining (RUM) technology; surface quality; cutting parameters; SANDWICH PANELS; BEHAVIOR;
D O I
10.3390/cryst12050725
中图分类号
O7 [晶体学];
学科分类号
0702 ; 070205 ; 0703 ; 080501 ;
摘要
Honeycomb composites (HCs) are diversely employed in aerospace, national defense and other fields owing to their remarkable spatial geometry and excellent mechanical properties. Their complex hexagonal cell structure and heterogeneous material properties cause major problems when implementing high-quality processing. Surface defects generated by processing will reduce the capability and service lifespan of the honeycomb sandwich structure. Therefore, the high quality of HCs is a topic of close attention for researchers. In this paper, the consequences of different cutting parameters of rotary ultrasonic machining (RUM) on surface quality with an ultrasonic circular knife (UCK) were studied through multiple groups of single-factor and orthogonal experiments with two-factors/four-levels and one-factor/three-levels. The single factor experiment was used to explain the effect that the degree of cutting parameters has on surface quality, and the orthogonal experiments were applied to explain the interaction between the processing parameters and the influence law of each factor on surface quality. Therefore, the reasonable cutting parameters of HCs were determined through experimental results to provide guidance for the realization of the precise and efficient machining of HCs. This study can provide a basis for the subsequent comprehensive consideration of various factors to achieve high-quality machining of HCs.
引用
收藏
页数:18
相关论文
共 50 条
  • [1] Experimental study on rotary ultrasonic machining (RUM) characteristics of Nomex honeycomb composites (NHCs) by circular knife cutting tools
    Ahmad, Shahzad
    Zhang, Jianfu
    Feng, Pingfa
    Yu, Dingwen
    Wu, Zhijun
    JOURNAL OF MANUFACTURING PROCESSES, 2020, 58 (58) : 524 - 535
  • [2] Numerical study on rotary ultrasonic machining (RUM) characteristics of Nomex honeycomb composites (NHCs) by UCSB cutting tool
    Zarrouk, Tarik
    Nouari, Mohammed
    Salhi, Jamal-Eddine
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2024, 132 (11-12): : 5351 - 5366
  • [3] Numerical study on rotary ultrasonic machining (RUM) characteristics of Nomex honeycomb composites (NHCs) by UCSB cutting tool
    Zarrouk, Tarik
    Nouari, Mohammed
    Salhi, Jamal-Eddine
    International Journal of Advanced Manufacturing Technology, 1600, 132 (11-12): : 5351 - 5366
  • [4] Experimental study on cutting force in rotary ultrasonic machining of zirconia/alumina composites
    Li, ZC
    Pei, ZJ
    Kwon, P
    Zeng, WM
    Treadwell, C
    Transactions of the North American Manufacturing Research Institution of SME 2005, Vol 33, 2005, 2005, 33 : 89 - 96
  • [5] Experimental studies on drilling tool load and machining quality of C/SiC composites in rotary ultrasonic machining
    Ding, Kai
    Fu, Yucan
    Su, Honghua
    Chen, Yan
    Yu, Xizhai
    Ding, Guozhi
    JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2014, 214 (12) : 2900 - 2907
  • [6] Rotary ultrasonic machining of SiCp/Al composites: An experimental study on cutting force and machinability
    Wang, Ming
    Zheng, Wei
    Zhou, Ming
    Zhang, Qun
    ADVANCES IN MECHANICAL ENGINEERING, 2019, 11 (12)
  • [7] Modeling of tool blockage condition in cutting tool design for rotary ultrasonic machining of composites
    Songmei Yuan
    Guangyuan Zhu
    Chong Zhang
    The International Journal of Advanced Manufacturing Technology, 2017, 91 : 2645 - 2654
  • [8] Modeling of tool blockage condition in cutting tool design for rotary ultrasonic machining of composites
    Yuan, Songmei
    Zhu, Guangyuan
    Zhang, Chong
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2017, 91 (5-8): : 2645 - 2654
  • [9] Research on Design and FE Simulations of Novel Ultrasonic Circular Saw Blade (UCSB) Cutting Tools for Rotary Ultrasonic Machining of Nomex Honeycomb Composites
    Ahmad, Shahzad
    Zhang, Jianfu
    Feng, Pingfa
    Yu, Dingwen
    Wu, Zhijun
    Ke, Ma
    PROCEEDINGS OF 2019 16TH INTERNATIONAL BHURBAN CONFERENCE ON APPLIED SCIENCES AND TECHNOLOGY (IBCAST), 2019, : 113 - 119
  • [10] Rotary ultrasonic machining of carbon fiber reinforced plastic composites: An experimental study on cutting temperature
    Cong, W. L.
    Zou, Xiaotian
    Deines, T. W.
    Wu, Nan
    Wang, Xingwei
    Pei, Z. J.
    JOURNAL OF REINFORCED PLASTICS AND COMPOSITES, 2012, 31 (22) : 1516 - 1525