Characteristic of Low Temperature Carburized Austenitic Stainless Steel

被引:4
|
作者
Istiroyah [1 ]
Pamungkas, M. A. [1 ]
Saroja, G. [1 ]
Ghufron, M. [1 ]
Juwono, A. M. [1 ]
机构
[1] Brawijaya Univ, Fac Nat Sci, Phys Dept, Malang, Indonesia
关键词
D O I
10.1088/1757-899X/299/1/012048
中图分类号
O69 [应用化学];
学科分类号
081704 ;
摘要
Low temperature carburizing process has been carried out on austenitic stainless steel (ASS) type AISI 316L, that contain chromium in above 12 at%. Therefore, conventional heat treatment processes that are usually carried out at high temperatures are not applicable. The sensitization process due to chromium migration from the grain boundary will lead to stress corrosion crack and decrease the corrosion resistance of the steel. In this study, the carburizing process was carried out at low temperatures below 500 degrees C. Surface morphology and mechanical properties of carburized specimens were investigated using optical microscopy, non destructive profilometer, and Vicker microhardness. The surface roughness analysis show the carburising process improves the roughness of ASS surface. This improvement is due to the adsorption of carbon atoms on the surface of the specimen. Likewise, the hardness test results indicate the carburising process increases the hardness of ASS.
引用
收藏
页数:5
相关论文
共 50 条
  • [31] Microstructure and corrosion behavior of low temperature carburized AISI 304 stainless steel
    Liu, R. L.
    Wang, S.
    Wei, C. Y.
    Yan, M. F.
    Qiao, Y. J.
    [J]. MATERIALS RESEARCH EXPRESS, 2019, 6 (06):
  • [32] Low temperature fluidized bed nitriding of austenitic stainless steel
    Haruman, E.
    Sun, Y.
    Malik, H.
    Sutjipto, A. G. E.
    Mridha, S.
    Widi, K.
    [J]. HEAT TREATMENT OF MATERIALS, 2006, 118 : 125 - +
  • [33] Effect of layer thickness on the rolling-sliding wear behavior of low-temperature plasma-carburized austenitic stainless steel
    Sun, Y
    Bell, T
    [J]. TRIBOLOGY LETTERS, 2002, 13 (01) : 29 - 34
  • [34] Effect of Layer Thickness on the Rolling-Sliding Wear Behavior of Low-Temperature Plasma-Carburized Austenitic Stainless Steel
    Y. Sun
    T. Bell
    [J]. Tribology Letters, 2002, 13 : 29 - 34
  • [35] On the fatigue behavior of low-temperature gaseous carburized 316L austenitic stainless steel: Experimental analysis and predictive approach
    Liu, Zhe
    Zhang, Song
    Wang, Shuaihui
    Peng, Yawei
    Gong, Jianming
    Somers, Marcel A. J.
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2020, 793
  • [36] Low-temperature carburized high-alloyed austenitic stainless steels in PEMFC cathodic environment
    Maistro, Giulio
    Kante, Stefan
    Nyborg, Lars
    Cao, Yu
    [J]. SURFACES AND INTERFACES, 2021, 24
  • [37] Low temperature anodic nitriding of AISI 304 austenitic stainless steel
    Li, Yang
    Xu, Huizhong
    Zhu, Feng
    Wang, Liang
    [J]. MATERIALS LETTERS, 2014, 128 : 231 - 234
  • [38] Scratch resistance of low-temperature plasma nitrided and carburized martensitic stainless steel
    Rovani, Ane C.
    Breganon, Rogerio
    de Souza, Gismar S.
    Brunatto, Silvio F.
    Pintaude, Giuseppe
    [J]. WEAR, 2017, 376 : 70 - 76
  • [39] MATERIAL PROPERTIES OF AUSTENITIC STAINLESS-STEEL AT LOW-TEMPERATURE
    KOTETSU, Y
    [J]. TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN, 1986, 72 (13): : 1368 - 1368
  • [40] Response of cast austenitic stainless steel to low temperature plasma carburizing
    Sun, Y.
    [J]. MATERIALS & DESIGN, 2009, 30 (04): : 1377 - 1380