Nanoscale Tribological Properties of Nanostructure Fe3Al and (Fe,Ti)3Al Compounds Fabricated by Spark Plasma Sintering Method

被引：1

作者：

Taghvaei, Mohammad Mahdi ^{[1
]}

Mostaan, Hossein ^{[1
]}

Rafiei, Mahdi ^{[2
]}

Bakhsheshi-Rad, Hamid Reza ^{[2
]}

Berto, Filippo ^{[3
]}

机构：

[1] Arak Univ, Fac Engn, Dept Mat & Met Engn, Arak 3815688349, Iran

[2] Islamic Azad Univ, Adv Mat Res Ctr, Dept Mat Engn, Najafabad Branch, Najafabad, Iran

[3] Norwegian Univ Sci & Technol, Dept Mech & Ind Engn, N-7491 Trondheim, Norway

来源：

METALS | 2022年 / 12卷 / 07期

关键词：

iron aluminides; spark plasma sintering; nanoscratch; nanohardness; mechanical alloying; STAINLESS-STEEL POWDERS; NANO-STRUCTURED DUPLEX; MECHANICAL-PROPERTIES; FE3AL-BASED ALLOYS; THERMODYNAMIC ANALYSIS; PHASE-FORMATION; AL; MICROSTRUCTURE; NANOCRYSTALLINE; BEHAVIOR;

D O I：

10.3390/met12071077

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Nanostructured powder particles of Fe3Al and (Fe,Ti)(3)Al phases were produced using mechanical alloying. These intermetallic phases with a nearly complete density were consolidated by spark plasma sintering. The mechanical properties of the bulk samples, i.e., elasticity modulus, hardness, and plasticity index, and also their tribological behavior were investigated using nanoindentation and nano-scratch tests. It was found that both Fe3Al and (Fe,Ti)(3)Al phases can be synthesized after 30 h of high-energy ball milling. In addition, no phase evolution was observed after spark plasma sintering. An analysis of the atomic force microscope images obtained from the nanoindentation tests showed a higher elasticity modulus, higher hardness, and lower plasticity index due to the addition of Ti to the Fe3Al system. (Fe,Ti)(3)Al displayed better tribological properties as compared with Fe3Al. A smaller volume of the scratched line was clearly seen in the atomic force microscope images of the nanostructured (Fe,Ti)(3)Al compound.

引用

页数：14

共 50 条

[21] Magnetic Properties of Disordered Fe3Al
Nehra, J.
Kabra, K.
Jani, S.
Ranjith, P. M.
Lakshmi, N.
Venugopalan, K.
SOLID STATE PHYSICS: PROCEEDINGS OF THE 55TH DAE SOLID STATE PHYSICS SYMPOSIUM 2010, PTS A AND B, 2011, 1349 : 1191 - 1192
[22] On the ordering in Fe3Al
Rafaja, D
Kratochvil, P
Kopecek, J
SCRIPTA MATERIALIA, 1996, 34 (09) : 1387 - 1392
[23] Diffusion in Fe3Al
Tokei, Z
Bernardini, J
Erdelyi, G
Gas, P
Beke, DL
SOLID STATE PHENOMENA, 1997, 56 : 181 - 181
[24] FRACTURE OF FE3AL
KERR, WR
METALLURGICAL TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 1986, 17 (12): : 2298 - 2300
[25] Decomposition of Al2.7Fe0.3Ti in heated Al-Al2.7Fe0.3Ti refiner fabricated by spark plasma sintering and its refining performance
Watanabe, Yoshimi
Hamada, Takayuki
Sato, Hisashi
JAPANESE JOURNAL OF APPLIED PHYSICS, 2017, 56 (01)
[26] Influence of iron powder particle size on the microstructure and properties of Fe3Al intermetallics prepared by mechanical alloying and spark plasma sintering
He, Qing
Ha, Chengchang
Meng, He
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2006, 428 (1-2): : 314 - 318
[27] Effect of severe plastic deformation on the structure and low-temperature internal friction of Fe3Al and (Fe,Cr)3Al
T. S. Pavlova
I. S. Golovin
D. V. Gunderov
C. Siemers
The Physics of Metals and Metallography, 2008, 105 : 36 - 44
[28] High-Temperature Oxidation of Fe3Al and Fe3Al–Zr Intermetallics
S. Chevalier
P. Juzon
G. Borchardt
A. Galerie
K. Przybylski
J. P. Larpin
Oxidation of Metals, 2010, 73 : 43 - 64
[29] Effect of severe plastic deformation on the structure and low-temperature internal friction of Fe3Al and (Fe,Cr)3Al
Pavlova, T. S.
Golovin, I. S.
Gunderov, D. V.
Siemers, C.
PHYSICS OF METALS AND METALLOGRAPHY, 2008, 105 (01): : 36 - 44
[30] Effect of technical parameters on nanostructure and mechanical properties of the bulk nanocrystalline Fe3Al
La, Pei-Qing
Lu, Rui-Jiao
Wang, Li
Cailiao Gongcheng/Journal of Materials Engineering, 2010, (07): : 18 - 23

← 1 2 3 4 5 →