Microstructure and corrosion resistance of stainless steel produced by bypass coupling twin-wire indirect arc additive manufacturing

被引：9
|
作者：
Wu, Dongting [1 ]
An, Qi [2 ]
Du, Fuxin [3 ]
Matsuda, Kenji [4 ]
Tang, Yingwen [5 ]
Zou, Yong [6 ]
机构：
[1] Shandong Univ, Key Lab Liquid Solid Struct Evolut & Proc Mat, Minist Educ, Jinan 250061, Peoples R China
[2] Shandong Univ, Sch Mat Sci & Engn, Jinan 250061, Peoples R China
[3] Shandong Univ, Sch Mech Engn, Jinan 250061, Peoples R China
[4] Univ Toyama, Dept Mat Design & Engn MaDE, Toyama 9308555, Japan
[5] Chinese Petr Soc, Beijing 100724, Peoples R China
[6] Shandong Univ, Shandong Engn & Technol Res Ctr Modern Welding, Jinan 250061, Peoples R China
来源：
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY | 2022年 / 119卷 / 3-4期
基金：
中国国家自然科学基金;
关键词：
Additive manufacturing; Bypass coupling twin-wire indirect arc welding; Droplet transfer; Intergranular corrosion resistance; Pitting corrosion resistance; RESIDUAL-STRESS; WAAM;
D O I：
10.1007/s00170-021-08343-1
中图分类号：
TP [自动化技术、计算机技术];
学科分类号：
0812 ;
摘要：
This study investigates the application of bypass coupling twin-wire indirect arc welding (BC-TWIAW) in arc additive manufacturing of 18-8 stainless steel. It is found that the droplet transfer changed from short circuit mode to stable spray mode with the welding current rising. Droplet transfer was the most stable when welding current was 200 A. Compared with the conventional MIG welding arc additive manufacturing, the efficiency of BC-TWIAW additive manufacturing can be increased by more than 30%. Electrochemical tests show that the BC-TWIAW overlay has a lower reactivation rate, higher charge transfer resistance, and lower carrier concentration, indicating that the overlay has better resistance to intergranular corrosion and pitting corrosion.
引用
收藏
页码：2159 / 2172
页数：14
相关论文
共 50 条
  • [31] Microstructure and corrosion resistance properties of 5356 aluminum alloy fabricated by wire and arc additive manufacturing
    Liang, Jingheng
    Zheng, Ziqin
    Xu, Zhibao
    Wang, Shuai
    Han, Han
    CAILIAO GONGCHENG-JOURNAL OF MATERIALS ENGINEERING, 2025, 53 (02):
  • [32] Analysis of Droplet Transfer and Arc Swing in "TIG plus AC" Twin-Wire Cross Arc Additive Manufacturing
    Song, Xueping
    Li, Zhuoxuan
    Huang, Jiankang
    Fan, Ding
    Yu, Shurong
    METALS, 2023, 13 (01)
  • [33] Effect of Al content on the microstructure and mechanical properties of γ-TiAl alloy fabricated by twin-wire plasma arc additive manufacturing system
    Wang, Lin
    Shen, Chen
    Zhang, Yuelong
    Li, Fang
    Huang, Ye
    Ding, Yuhan
    Xin, Jianwen
    Zhou, Wenlu
    Hua, Xueming
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2021, 826
  • [34] Fabrication of ?-TiAl intermetallic alloy using the twin-wire plasma arc additive manufacturing process: Microstructure evolution and mechanical properties
    Wang, Lin
    Zhang, Yuelong
    Hua, Xueming
    Shen, Chen
    Li, Fang
    Huang, Ye
    Ding, Yuhan
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2021, 812
  • [35] Wire-arc additive manufacturing of a duplex stainless steel: thermal cycle analysis and microstructure characterization
    Hosseini, Vahid A.
    Hogstrom, Mats
    Hurtig, Kjell
    Bermejo, Maria Asuncion Valiente
    Stridh, Lars-Erik
    Karlsson, Leif
    WELDING IN THE WORLD, 2019, 63 (04) : 975 - 987
  • [36] Wire-arc additive manufacturing of a duplex stainless steel: thermal cycle analysis and microstructure characterization
    Vahid A Hosseini
    Mats Högström
    Kjell Hurtig
    Maria Asuncion Valiente Bermejo
    Lars-Erik Stridh
    Leif Karlsson
    Welding in the World, 2019, 63 : 975 - 987
  • [37] Influence of Shielding Gas on the Microstructure and Mechanical Properties of Duplex Stainless Steel in Wire Arc Additive Manufacturing
    Akbarzadeh, Elina
    Yurtisik, Koray
    Gur, C. Hakan
    Saeid, Tohid
    Tavangar, Reza
    METALS AND MATERIALS INTERNATIONAL, 2024, 30 (07) : 1977 - 1996
  • [38] The Effect of a Slow Strain Rate on the Stress Corrosion Resistance of Austenitic Stainless Steel Produced by the Wire Laser Additive Manufacturing Process
    Bassis, Maxim
    Kotliar, Abram
    Koltiar, Rony
    Ron, Tomer
    Leon, Avi
    Shirizly, Amnon
    Aghion, Eli
    METALS, 2021, 11 (12)
  • [39] Microstructure and Corrosion Properties of Stainless Steel 308L Prepared by Cold Metal Transfer-Wire Arc Additive Manufacturing
    Wang, Xiaoli
    Hu, Qingxian
    Liu, Wenkang
    Chen, Fugang
    Xiao, Nan
    Zhan, Shangwen
    JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2024, 33 (20) : 10736 - 10744
  • [40] Microstructure and mechanical properties of H13 steel block produced by wire arc additive manufacturing
    Yang, Linpo
    Lin, Jian
    Zhu, Bingyue
    Zhang, Yongqiang
    Sun, Qisong
    Fu, Hanguang
    Lei, Yongping
    MATERIALS LETTERS, 2024, 358
12345