Application of quality by design for optimization of spray drying process used in drying of Risperidone nanosuspension

被引:33
|
作者
Nair, Anu [1 ]
Khunt, Dignesh [1 ]
Misra, Manju [1 ]
机构
[1] NIPER Ahmedabad, Dept Pharmaceut, Palaj Opp Airforce Stn Headquarter, Gandhinagar 382355, Gujarat, India
关键词
Nanosuspension; Spray drying; QbD; Risperidone; Orally dispersible tablet; PHYSICOCHEMICAL PROPERTIES; DRUG; FORMULATION; DELIVERY; NANOPARTICLE; CONVERSION; POWDERS;
D O I
10.1016/j.powtec.2018.09.096
中图分类号
TQ [化学工业];
学科分类号
0817 ;
摘要
The objective of present study was to optimize spray drying of Risperidone (RIS) nanosuspension for achieving lower particle size, higher yield and good compressibility of spray dried powder using Quality by design approach. RIS nanosuspension was prepared by anti-solvent precipitation technique using poloxamer 68 and Poloxamer 127 as stabilizers. 3 level 2 factorial design was applied using two independent factor variables viz., X1: feed pump speed (RPM) and X2: inlet temperature (degrees C) and their effect upon dependent variables viz., Y1: Size, and Y2: %Entrapment efficiency was determined at three different levels. Spray dried powder was further characterized for bulk level properties and formulated as an orally dispersible tablet (ODT). The developed ODT were characterized by various parameters like wetting time, disintegration time, hardness, friability, weight variation and dissolution for comparison. Size and PDI of formulated RIS Nanosuspension were found to be 200.00 +/- 0.40 nm and 0210 +/- 0.03 respectively. Optimized process parameters for spray dryer were obtained from design space, which gave critical quality attributes (CQA) response of lowest size and highest yield of 214.21 +/- 2.01 nm and 61.85 +/- 1.02% respectively. FTIR, DSC, XRD and AFM studies of spray dried RIS nanosuspension revealed that crystallinity of RIS was altered during spray drying process. Bulk density, Tapped density, Hausner ratio, Compressibility index and Angle of repose of spray dried RIS was found to be 0.588 +/- 0.12 g/mL, 0.641 +/- 0.20 g/mL, 1.09 +/- 0.26, 8.33 +/- 0.32 and 32.40 degrees +/- 0.98 degrees respectively. ODT formulated using optimized spray dried nanosuspension showed higher dissolution than marketed ODT formulation which may be due to increase in solubility of Risperidone during spray drying of nanosuspension. (C) 2018 Elsevier B.V. All rights reserved.
引用
收藏
页码:156 / 165
页数:10
相关论文
共 50 条
  • [21] Optimization of brewer's yeast spray drying process
    Luna-Solano, G
    Salgado-Cervantes, MA
    Rodríguez-Jimenes, GC
    García-Alvarado, MA
    JOURNAL OF FOOD ENGINEERING, 2005, 68 (01) : 9 - 18
  • [22] Spray freeze drying to solidify Nanosuspension of Cefixime into inhalable microparticles
    Dorrin Mohtadi Haghighi
    Homa Faghihi
    Majid Darabi
    Maryam Saadat Mirmoeini
    Alireza Vatanara
    DARU Journal of Pharmaceutical Sciences, 2022, 30 : 17 - 27
  • [23] Strategizing Spray Drying Process Optimization for the Manufacture of Redispersible Indomethacin Nanoparticles Using Quality-by-Design Principles
    Vishal Rathod
    Bhavin Gajera
    Anusha Pinninti
    Irfan A. Mohammed
    Rutesh H. Dave
    AAPS PharmSciTech, 24
  • [24] Strategizing Spray Drying Process Optimization for the Manufacture of Redispersible Indomethacin Nanoparticles Using Quality-by-Design Principles
    Rathod, Vishal
    Gajera, Bhavin
    Pinninti, Anusha
    Mohammed, Irfan A. A.
    Dave, Rutesh H. H.
    AAPS PHARMSCITECH, 2023, 24 (05)
  • [25] Rheological characterization of polymeric solutions used in spray drying process
    Porfirio, Tiago
    Galindo-Rosales, Francisco J.
    Campo-Deano, Laura
    Vicente, Joao
    Semiao, Viriato
    EUROPEAN JOURNAL OF PHARMACEUTICAL SCIENCES, 2021, 158
  • [26] Spray freeze drying to solidify Nanosuspension of Cefixime into inhalable microparticles
    Haghighi, Dorrin Mohtadi
    Faghihi, Homa
    Darabi, Majid
    Mirmoeini, Maryam Saadat
    Vatanara, Alireza
    DARU-JOURNAL OF PHARMACEUTICAL SCIENCES, 2022, 30 (01) : 17 - 27
  • [27] Application of pulse combustion technology in spray drying process
    Zbicinski, I
    Smucerowicz, I
    Strumillo, C
    Crowe, C
    BRAZILIAN JOURNAL OF CHEMICAL ENGINEERING, 2000, 17 (4-7) : 441 - 450
  • [28] Application of pulse combustion technology in spray drying process
    Zbicinski, I.
    Smucerowicz, I.
    Strumillo, C.
    Crowe, C.
    Brazilian Journal of Chemical Engineering, 2000, 17 (04) : 441 - 450
  • [29] Spray Drying of Yogurt: Optimization of Process Conditions for Improving Viability and Other Quality Attributes
    Koc, Banu
    Yilmazer, Melike Sakin
    Balkir, Pinar
    Ertekin, Figen Kaymak
    DRYING TECHNOLOGY, 2010, 28 (04) : 495 - 507
  • [30] CFD modeling of baijiu yeast spray drying process and improved design of drying tower
    Xiong, Fengkui
    Yuan, Yuejin
    Liu, Kang
    Tan, Libin
    Li, Jingyu
    Zhao, Zhe
    DRYING TECHNOLOGY, 2024, 42 (05) : 836 - 853