Hydrogen Induced Stress Corrosion Cracking of Fuel Oil Premix Burner Nozzles in a Heavy-duty Gas Turbine Engine

被引：0
|
作者：
Neidel, A. [1 ]
Gadicke, T. [1 ]
Wallich, S. [1 ]
机构：
[1] Siemens AG, Power & Gas, Gasturbinenwerk Berlin, Werkslab, Huttenstr 12, D-10548 Berlin, Germany
来源：
PRAKTISCHE METALLOGRAPHIE-PRACTICAL METALLOGRAPHY | 2018年 / 55卷 / 11期
关键词：
D O I：
10.3139/147.110499
中图分类号：
TF [冶金工业];
学科分类号：
0806 ;
摘要：
A number of M8 fuel oil pre-mix (FOPM) burner nozzles in a heavy-duty gas turbine engine were found loosened after some 32,000 operating hours. They were removed and tended to crack in the shaft upon disassembly. It was determined on site that they were fractured at the fillet radius below the head, at the thread's end. A metallurgical root cause investigation was ordered to determine the cause of the cracking. Selected dimensional checks, chemical analyses, microstructural examinations, and evaluations of fuel oil analyses conducted by external sources were performed to achieve the required results. Fractographic studies were not possible in this case due to the corrosion products covering the fracture surfaces. The FOPM burner nozzles fractured due to hydrogen-induced stress corrosion cracking (HISCC). No evidence of pre-existing cracks was found. There are no signs of over-torqueing nor of any other damage caused by manufacturing or assembly; hence this failure was caused by engine service and is not fabrication related.
引用
收藏
页码：773 / 786
页数：14
相关论文
共 50 条
  • [1] Metallurgical Failure Investigation of HCF Cracking in a Premix Fuel Oil Manifold of a Heavy-duty Combined Cycle Gas Turbine Engine
    Neidel, A.
    Fischer, B.
    Cagliyan, E.
    PRAKTISCHE METALLOGRAPHIE-PRACTICAL METALLOGRAPHY, 2016, 53 (04): : 237 - 247
  • [2] Uncharacteristic Circumferential TMF Cracking in a Heavy-duty Stationary Gas Turbine Engine Burner Outlet
    Neidel, A.
    Ullrich, Th.
    Wallich, S.
    PRAKTISCHE METALLOGRAPHIE-PRACTICAL METALLOGRAPHY, 2015, 52 (06): : 334 - 341
  • [3] Fretting Fatigue Cracking of an Arresting Feature in a Turbine Disk of a Heavy-Duty Gas Turbine Engine
    Neidel, A.
    Giller, M.
    Riesenbeck, S.
    PRAKTISCHE METALLOGRAPHIE-PRACTICAL METALLOGRAPHY, 2018, 55 (01): : 37 - 46
  • [4] High Cycle Fatigue Failure of Burner Feeder Line in a Heavy-duty Gas Turbine Engine
    Neidel, A.
    Giller, M.
    Riesenbeck, S.
    Woehl, E.
    PRAKTISCHE METALLOGRAPHIE-PRACTICAL METALLOGRAPHY, 2019, 56 (01): : 48 - 60
  • [5] Pollutant Emission Validation of a Heavy-Duty Gas Turbine Burner by CFD Modeling
    Meloni, Roberto
    MACHINES, 2013, 1 (03) : 81 - 97
  • [6] An investigation of the combustion process of a heavy-duty dual fuel engine supplemented with natural gas or hydrogen
    Li, H.
    Liu, S.
    Liew, C.
    Gatts, T.
    Wayne, S.
    Clark, N.
    Nuszkowski, J.
    INTERNATIONAL JOURNAL OF HYDROGEN ENERGY, 2017, 42 (05) : 3352 - 3362
  • [7] Fretting Fatigue Cracking of a Center Guide Bolt Supporting the Combustion Chamber in a Heavy-duty Gas Turbine Engine
    Neidel, A.
    Fischer, B.
    Gaedicke, T.
    PRAKTISCHE METALLOGRAPHIE-PRACTICAL METALLOGRAPHY, 2018, 55 (03): : 158 - 175
  • [8] Study of an Experiment System and Flow Measurement of Group Nozzles in A Heavy-Duty Gas Turbine
    Xuli
    Liukai
    MECHANICAL, MATERIALS AND MANUFACTURING ENGINEERING, PTS 1-3, 2011, 66-68 : 311 - +
  • [9] Integrated experimental and numerical approach for fuel-air mixing prediction in a heavy-duty gas turbine LP burner
    Mori, G
    Razore, S
    Ubaldi, M
    Zunino, P
    JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME, 2001, 123 (04): : 803 - 809
  • [10] AERODYNAMIC ANALYSIS AND REDESIGN OF AN INLET SEGMENT FOR A HEAVY-DUTY GAS TURBINE ENGINE
    Abdel-Wahab, Samer
    Vogel, Gregory
    PROCEEDINGS OF THE ASME TURBO EXPO 2010: TURBOMACHINERY: AXIAL FLOW FAN AND COMPRESSOR AERODYNAMICS DESIGN METHODS, AND CFD MODELING FOR TURBOMACHINERY, VOL 7, PTS A-C, 2010, : 1275 - 1282
12345