Study of the adhered material to the cutting tools on dry turning of aluminium alloys

被引：0
|
作者：
De Agustina, Beatriz
Rubio, Eva
Marcos, Mariano
机构：
来源：
ANNALS OF DAAAM FOR 2007 & PROCEEDINGS OF THE 18TH INTERNATIONAL DAAAM SYMPOSIUM: INTELLIGENT MANUFACTURING & AUTOMATION: FOCUS ON CREATIVITY, RESPONSIBILITY, AND ETHICS OF ENGINEERS | 2007年
关键词：
dry machining; short cutting tests; UNS A97050-T7; tool wear;
D O I：
暂无
中图分类号：
TP [自动化技术、计算机技术];
学科分类号：
0812 ;
摘要：
In this study the relationship between the applied cutting parameters and the change to the tool geometry produced by material adhesion was analysed. Namely, a series of tests of dry turning of short duration (no longer than ten seconds) were carried out using a workpiece of aluminium UNS A97050-T7. Different cutting conditions were employed using uncoated based on WC-Co tools. The quantity of material adhered to the tool were measured by macroscopic techniques. As a first conclusion, it is possible to affirm that there is a higher material adherence using higher feeds.
引用
收藏
页码：215 / 216
页数：2
相关论文
共 50 条
  • [31] Design and experimental study of turning tools with linear cutting edges and comparison to commercial tools
    Peter Monka
    Katarina Monkova
    Milan Balara
    Sergej Hloch
    Jan Rehor
    Andrej Andrej
    Matej Somsak
    The International Journal of Advanced Manufacturing Technology, 2016, 85 : 2325 - 2343
  • [32] An experimental investigation of the effect of coatings and cutting parameters on the dry drilling performance of aluminium alloys
    Rivero, A
    Aramendi, G
    Herranz, S
    de Lacalle, LNL
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2006, 28 (1-2): : 1 - 11
  • [33] An experimental investigation of the effect of coatings and cutting parameters on the dry drilling performance of aluminium alloys
    A. Rivero
    G. Aramendi
    S. Herranz
    L.N. López de Lacalle
    The International Journal of Advanced Manufacturing Technology, 2006, 28 : 1 - 11
  • [34] Influence of cutting parameters on cutting forces and surface roughness in dry turning of Al using PCD and different coated tools
    Kumar, R.
    Pattnaik, S. K.
    Minz, J. K.
    Padhi, S.
    Sarangi, S. K.
    SADHANA-ACADEMY PROCEEDINGS IN ENGINEERING SCIENCES, 2019, 44 (08):
  • [35] Influence of cutting parameters on cutting forces and surface roughness in dry turning of Al using PCD and different coated tools
    R Kumar
    S K Pattnaik
    J K Minz
    S Padhi
    S K Sarangi
    Sādhanā, 2019, 44
  • [36] Wear and MnS Layer Adhesion in Uncoated Cutting Tools When Dry and Wet Turning Free-Cutting Steels
    Martinez Krahmer, D.
    Hameed, S.
    Sanchez Egea, A. J.
    Perez, D.
    Canales, J.
    Lopez de Lacalle, L. N.
    METALS, 2019, 9 (05)
  • [37] Comparison Research on the Machinability of Hardened Steel when Dry Turning with Ceramic and CBN Cutting Tools
    Tu, Chunjuan
    Guo, Xuhong
    Wang, Wei
    Wang, Chihong
    ADVANCES IN MECHATRONICS TECHNOLOGY, 2011, 43 : 573 - 577
  • [38] Cutting performance and wear mechanisms of Sialon ceramic cutting tools at high speed dry turning of gray cast iron
    Tu, Guizhao
    Wu, Shanghua
    Liu, Jia
    Long, Ying
    Wang, Bo
    INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS, 2016, 54 : 330 - 334
  • [39] FEM machining analysis: influence of rake angle in cutting of aluminium alloys using Polycrystalline Diamond cutting tools
    Maranhao, C.
    Davim, J. Paulo
    Jackson, M. J.
    Cabral, G.
    Gracio, J.
    INTERNATIONAL JOURNAL OF MATERIALS & PRODUCT TECHNOLOGY, 2010, 37 (1-2): : 199 - 213
  • [40] FEM machining analysis: Influence of rake angle in cutting of aluminium alloys using Polycrystalline Diamond cutting tools
    Maranhão C.
    Davim J.P.
    Jackson M.J.
    Cabral G.
    Grácio J.
    International Journal of Materials and Product Technology, 2010, 37 (1-2) : 199 - 213
12345