Indirect Monitoring Method of Tool Wear using the Analysis of Cutting Force during Dry Machining of Ti Alloys

被引：9

作者：

Sanchez, Y. ^{[1
]}

Trujillo, F. J. ^{[1
]}

Sevilla, L. ^{[1
]}

Maroc, M. ^{[2
]}

机构：

[1] Univ Malaga, Dept Management Engn, C Dr Ortiz Ramos S-N, E-29071 Malaga, Spain

[2] Univ Cadiz, Dept Mech Engn & Ind Design, Puerto Real, E-11510 Cadiz, Spain

来源：

MANUFACTURING ENGINEERING SOCIETY INTERNATIONAL CONFERENCE 2017 (MESIC 2017) | 2017年 / 13卷

关键词：

Titanium alloys; Orthogonal cutting; Cutting force; Chip morphology; Wear mechanisms;

D O I：

10.1016/j.promfg.2017.09.127

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Tool life optimization is in constant evolution; so many researchers have focused applied different measuring techniques for the tool wear because plays a significant role in the control and improvement of product during machining operations, in real time. Titanium alloys are widely used in many industries of strategic interest as aerospace sector, in the manufacturing of parts with a good strength to weight ratio. These alloys usually show a poor machinability, due to their low thermal conductivity and modulus of elasticity, which may increase the cutting temperature and make the tool breakage more likely. This paper presents a methodology for the tool wear monitoring by using the analysis of cutting forces during dry machining of Titanium alloys. (C) 2017 The Authors. Published by Elsevier B.V.

引用

页码：623 / 630

页数：8

共 50 条

[31] The relationship between the cutting speed, tool wear, and chip formation during Ti-5553 dry cutting
Vincent Wagner
Maher Baili
Gilles Dessein
[J]. The International Journal of Advanced Manufacturing Technology, 2015, 76 : 893 - 912
[32] The relationship between the cutting speed, tool wear, and chip formation during Ti-5553 dry cutting
Wagner, Vincent
Baili, Maher
Dessein, Gilles
[J]. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2015, 76 (5-8): : 893 - 912
[33] Machining of diamond by using tool wear during cutting of carbon steel: (Investigation into machining rate of diamond)
Nakamoto, Takeshi
Shabouk, Sohaib
Yamaguchi, Tsuyoshi
[J]. Nippon Kikai Gakkai Ronbunshu, C Hen/Transactions of the Japan Society of Mechanical Engineers, Part C, 2002, 68 (05): : 1582 - 1588
[34] Modeling of cutting forces in near dry machining under tool wear effect
Li, Kuan-Ming
Liang, Steven Y.
[J]. INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2007, 47 (7-8): : 1292 - 1301
[35] MONITORING OF TOOL WEAR DISTRIBUTION WITH CUTTING FORCE MEASUREMENT IN DRILLING
Tamura, Shoichi
Sekigawa, Kodai
Matsumura, Takashi
[J]. PROCEEDINGS OF THE JSME 2020 CONFERENCE ON LEADING EDGE MANUFACTURING/MATERIALS AND PROCESSING, LEMP2020, 2020,
[36] Monitoring of tool wear distribution with cutting force measurement in drilling
Tamura, Shoichi
Sekigawa, Kodai
Matsumura, Takashi
[J]. JOURNAL OF ADVANCED MECHANICAL DESIGN SYSTEMS AND MANUFACTURING, 2021, 15 (04):
[37] Indirect method of tool wear measurement and prediction using ANN network in machining process
Bagga, P. J.
Makhesana, M. A.
Patel, H. D.
Patel, K. M.
[J]. MATERIALS TODAY-PROCEEDINGS, 2021, 44 : 1549 - 1554
[38] Cutting Tool Wear Optimization in the Machining of Fly Ash Geopolymer using Taguchi Method
Fauziah, P. Y.
Fathullah, M.
Abdullah, M. M. A.
Faris, Meor Ahmad
Tahir, Faheem
Shayfull, Z.
Nasir, S. M.
Shazzuan, M.
Wazien, A. Z. W.
[J]. GREEN DESIGN AND MANUFACTURE: ADVANCED AND EMERGING APPLICATIONS, 2018, 2030
[39] Intelligent Robust Milling Tool Wear Monitoring via Fractal Analysis of Cutting Force
Liu, Tongshun
Zhu, Kunpeng
[J]. 2017 13TH IEEE CONFERENCE ON AUTOMATION SCIENCE AND ENGINEERING (CASE), 2017, : 1254 - 1259
[40] Investigation of Cutting Force Tool Tip Temperature and Surface Roughness during Dry Machining of Spring Steel
Vasu, M.
Nayaka, Shivananda H.
[J]. MATERIALS TODAY-PROCEEDINGS, 2018, 5 (02) : 7141 - 7149

← 1 2 3 4 5 →