Assessment and optimization of cutting parameters while turning AISI 52100 steel

被引：0
|
作者：
Sharma, Vishal S. [1 ]
Dhiman, Suresh [2 ]
Sehgal, Rakesh [2 ]
Sharma, Surinder Kumar [3 ]
机构：
[1] Natl Inst Technol, Dept Ind Engn, Jalandhar 144011, PB, India
[2] Natl Inst Technol, Dept Mech Engn, Hamirpur 177001, HP, India
[3] Natl Inst Technol, Dept Mech Engn, Kurukshetra 132118, Haryana, India
来源：
INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING | 2008年 / 9卷 / 02期
关键词：
cutting forces; tool tip temperature; surface roughness;
D O I：
暂无
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
This investigation deals with machining AISI 52100 steel using a carbide-coated tool. The machining cutting force and tool tip temperature are measured online while turning using different cutting parameters. The surface roughness is also measured, but off-line after each cut. The obtained data are analyzed and the influence of the cutting parameters on the machining variables is determined in the form of plots. Regression models obtained from the results are tested using additional experimental data.
引用
收藏
页码：54 / 62
页数：9
相关论文
共 50 条
  • [31] EXPERIMENTAL INVESTIGATION OF TOOL WEAR AND INDUCED VIBRATION IN TURNING HIGH HARDNESS AISI52100 STEEL USING CUTTING PARAMETERS AND TOOL ACCELERATION
    Ambhore, Nitin
    Kamble, Dinesh
    [J]. FACTA UNIVERSITATIS-SERIES MECHANICAL ENGINEERING, 2020, 18 (04) : 623 - 637
  • [32] Effect of cutting edge geometry and workpiece hardness on surface generation in the finish hard turning of AISI 52100 steel
    Thiele, JD
    Melkote, SN
    [J]. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 1999, 94 (2-3) : 216 - 226
  • [33] Evaluation of Cutting Tool Vibration and Surface Roughness in Hard Turning of AISI 52100 Steel: An Experimental and ANN Approach
    Nitin Ambhore
    Dinesh Kamble
    Satish Chinchanikar
    [J]. Journal of Vibration Engineering & Technologies, 2020, 8 : 455 - 462
  • [34] RSM Based Investigations on the Effects of Cutting Parameters on Surface Integrity during Cryogenic Hard Turning of AISI 52100
    Shihab, Suha K.
    Khan, Zahid A.
    Siddiquee, Arshad Noor
    [J]. JOURNAL FOR MANUFACTURING SCIENCE AND PRODUCTION, 2015, 15 (03) : 309 - 318
  • [35] Multi-objective optimization of cutting parameters during sustainable dry hard turning of AISI 52100 steel with newly develop HSN2-coated carbide insert
    Alok, Anupam
    Das, Manas
    [J]. MEASUREMENT, 2019, 133 : 288 - 302
  • [36] Effect of cutting edge geometry and workpiece hardness on surface generation in the finish hard turning of AISI 52100 steel
    Thiele, Jeffrey D.
    N. Melkote, Shreyes
    [J]. Journal of Materials Processing Technology, 1999, 94 (02): : 216 - 226
  • [37] Effects of Process Parameters on White Layer Formation and Morphology in Hard Turning of AISI52100 Steel
    Zhang, Xiao-Ming
    Chen, Li
    Ding, Han
    [J]. JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME, 2016, 138 (07):
  • [38] FE modeling of microstructural changes in hard turning of AISI 52100 steel
    G. L. Manco
    S. Caruso
    G. Rotella
    [J]. International Journal of Material Forming, 2010, 3 : 447 - 450
  • [39] A Multivariate Statistical Quality Control of AISI 52100 Hardened Steel Turning
    Evangelista, George
    Peruchi, Rogerio Santana
    Brito, Tarcisio Goncalves
    Rotela Junior, Paulo
    Souza Rocha, Luiz Celio
    [J]. IEEE ACCESS, 2020, 8 (08): : 109092 - 109104
  • [40] Analysis of white layers formed in hard turning of AISI 52100 steel
    Ramesh, A
    Melkote, SN
    Allard, LF
    Riester, L
    Watkins, TR
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2005, 390 (1-2): : 88 - 97
12345