Study of Exit Burr Formation of CFRP

被引：8
|
作者：
Ji, W. [1 ]
Wang, Y. W. [1 ]
Li, Y. F. [1 ]
Yan, F. G. [1 ]
Liu, X. L. [1 ]
机构：
[1] Harbin Univ Sci & Tech, Key Lab Adv Mfg Tech & Cutting Tools, Harbin 150080, Peoples R China
来源：
HIGH SPEED MACHINING | 2011年 / 188卷
关键词：
CFRP; Burr; Fiber direction; Tool geometry;
D O I：
10.4028/www.scientific.net/AMR.188.154
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
Microcosmic and macroscopic form of CFRP holes drilled by new PCD tool were observed in this paper. Location and distribution of burr and fiber direction of burr were analyzed, and formation mechanism of burr of CFRP hole exit is studied tentatively. The methods of inhibit the formation of burr formation were put forward from the design principles of the tool geometry parameters.
引用
收藏
页码：154 / 157
页数：4
相关论文
共 50 条
  • [31] Analytical modelling of slot milling exit burr size
    Seyed Ali Niknam
    Victor Songmene
    The International Journal of Advanced Manufacturing Technology, 2014, 73 : 421 - 432
  • [32] Simulation of burr formation during machining: case study
    Zebala, Wojciech
    Rumian, Ksenia
    PHOTONICS APPLICATIONS IN ASTRONOMY, COMMUNICATIONS, INDUSTRY, AND HIGH-ENERGY PHYSICS EXPERIMENTS 2018, 2018, 10808
  • [33] Burr formation in grinding
    Wong, YC
    Doyle, ED
    ABRASIVE TECHNOLOGY: CURRENT DEVELOPMENT AND APPLICATIONS I, 1999, : 103 - 108
  • [34] Effect of the chip thickness and the exit angle on the burr formation and break-out of the workpiece edge in the case of milling
    Poka, Gyorgy
    Balazs, Barnabas Zoltan
    JOURNAL OF MANUFACTURING PROCESSES, 2024, 111 : 45 - 63
  • [35] Parameters Optimization of Axial Vibration Drilling Based on the Exit Burr
    Wang Huilin
    Zhang Pingkuan
    Li Qiaoying
    MECHANICAL ENGINEERING, MATERIALS SCIENCE AND CIVIL ENGINEERING II, 2014, 470 : 429 - 432
  • [36] Burr Measurement System for Drilled Hole at Inclined Exit Surface
    Hoang, H. P.
    Ko, S. L.
    BURRS - ANALYSIS, CONTROL AND REMOVAL: PROCEEDINGS OF THE CIRP INTERNATIONAL CONFERENCE ON BURRS, 2009, 2010, : 157 - 165
  • [37] Calculating of the Exit Burr in Low Frequency Axial Vibration Drilling
    Wang Huilin
    Li Qiaoying
    Zhang Pingkuan
    MECHATRONICS AND INTELLIGENT MATERIALS III, PTS 1-3, 2013, 706-708 : 1231 - 1236
  • [38] Study on Burr Formation at the Top Edge in Rectangular Groove Cutting
    Deng, Wen Jun
    Xie, Zi Chun
    Lin, Ping
    Xu, Tong Kui
    ADVANCES IN MATERIALS SCIENCE AND ENGINEERING, 2012, 2012
  • [39] An experimental study of burr formation in square shoulder face milling
    Olvera, O
    Barrow, G
    INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 1996, 36 (09): : 1005 - 1020
  • [40] An experimental study on burr formation in micro milling aluminum and copper
    Lee, K
    Dornfeld, DA
    TRANSACTIONS OF THE NORTH AMERICAN MANUFACTURING RESEARCH INSTITUTE OF SME, VOL XXX, 2002, 2002, : 255 - 262
12345