Model of Pulse Power Generator in Electrical Discharge Machining (EDM) System

被引：4
|
作者：
Ade Erawan, Minhat [1 ]
Azli, Yahya [1 ]
Nor Hisham, Khamis [1 ]
Ahmad Saudi, Samosir [1 ]
Muhammad Arif, Abdul Rahim [1 ]
Trias, Andromeda [1 ]
Kartiko, Nugroho [2 ]
机构：
[1] Univ Teknol Malaysia, Fac Elect Engn, Skudai 81310, Johor, Malaysia
[2] Univ Teknol Malaysia, Fac Biosceinces & Med Engn, Skudai Johor 81310, Malaysia
来源：
MECHANICAL AND MATERIALS ENGINEERING | 2014年 / 554卷
关键词：
Electrical Discharge Machining; Pulse Power Generator; Current Gap; Voltage Gap;
D O I：
10.4028/www.scientific.net/AMM.554.613
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
Electrical discharge machining (EDM) is a non-traditional manufacturing process of removing material. EDM system consists of a shaped tool and the work piece, which are connected to a power supply and placed in a dielectric fluid. EDM pulse power generator applies voltage pulses between the electrode and workpiece to generate sparks through the gap. The essential requirement for EDM system is to obtain the output waveform similar to the ideal EDM waveform. The design is based on transistor type pulse power generator circuit. This paper discuss in modeling of current and voltage gap waveform for EDM system.
引用
收藏
页码：613 / +
页数：2
相关论文
共 50 条
  • [1] Power Generator of Electrical Discharge Machining (EDM) System
    Ade Erawan, Minhat
    Azli, Yahya
    Nor Hisham, Khamis
    Syahrullail, Samion
    Zurkarmawan, Abu Bakar
    Trias, Andromeda
    [J]. MECHANICAL AND MATERIALS ENGINEERING, 2014, 554 : 638 - +
  • [2] Control Strategy for Electrical Discharge Machining (EDM) Pulse Power Generator
    Ade Erawan, Minhat
    Nor Hisham, Khamis
    Azli, Yahya
    Trias, Andromeda
    Kartiko, Nugroho
    Nor Liyana Safura, Hashim
    Nazriah, Mahmud
    Razak, M.
    [J]. MECHANICAL AND MATERIALS ENGINEERING, 2014, 554 : 643 - +
  • [3] One-Cycle Control for Pulse Power Generator in Electrical-Discharge-Machining
    Yang, Fei
    Liu, Yayun
    Liu, Weihan
    Yao, Kai
    [J]. IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, 2022, 69 (11) : 11012 - 11022
  • [4] One-Cycle Control for Pulse Power Generator in Electrical-Discharge-Machining
    Yang, Fei
    Liu, Yayun
    Liu, Weihan
    Yao, Kai
    [J]. AMERICAN JOURNAL OF CLINICAL NUTRITION, 2021, : 11012 - 11022
  • [5] Development of an Economical System for Electrical Discharge Machining (EDM) in Water
    Medellin Castillo, Hugo I.
    Loredo Ramirez, J. Abraham
    [J]. PROCEEDINGS OF THE ASME INTERNATIONAL MECHANICAL ENGINEERING CONGRESS AND EXPOSITION 2010, VOL 3, PTS A AND B, 2012, : 983 - 992
  • [6] Pulse generator for obtaining surfaces of small dimensions by electrical discharge machining
    Coteata, Margareta
    Floca, Alexandru
    Dodun, Oana
    Ionescu, Nicolae
    Nagit, Gheorghe
    Slatineanu, Laurentiu
    [J]. 18TH CIRP CONFERENCE ON ELECTRO PHYSICAL AND CHEMICAL MACHINING (ISEM XVIII), 2016, 42 : 715 - 720
  • [7] Design and fabrication of control system-based ISO pulse generator for electrical discharge machining
    Muthuramalingam, T.
    Mohan, B.
    [J]. International Journal of Mechatronics and Manufacturing Systems, 2013, 6 (02) : 133 - 143
  • [8] Fast and stable electrical discharge machining (EDM)
    Wu, Jianyang
    Zhou, Ming
    Xu, Xiaoyi
    Yang, Jianwei
    Zeng, Xiangwei
    Xu, Donghui
    [J]. MECHANICAL SYSTEMS AND SIGNAL PROCESSING, 2016, 72-73 : 420 - 431
  • [9] State of the art electrical discharge machining (EDM)
    Ho, KH
    Newman, ST
    [J]. INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2003, 43 (13): : 1287 - 1300
  • [10] Design and Investigate of Flushing System for Electrical Discharge Machining (EDM) Application
    Rachmat, Haris
    Ibrahim, Rasidi
    Ming, Kee Hem
    Ismail, Al Emran
    Rahim, Zulafif
    Swangsari, Worapong
    [J]. INTERNATIONAL JOURNAL OF INTEGRATED ENGINEERING, 2020, 12 (02): : 218 - 225
12345