Control Strategy for Electrical Discharge Machining (EDM) Pulse Power Generator

被引：0

作者：

Ade Erawan, Minhat ^{[1
]}

Nor Hisham, Khamis ^{[1
]}

Azli, Yahya ^{[1
]}

Trias, Andromeda ^{[1
,2
]}

Kartiko, Nugroho ^{[2
]}

Nor Liyana Safura, Hashim ^{[2
]}

Nazriah, Mahmud ^{[2
]}

Razak, M. ^{[3
]}

机构：

[1] Univ Teknol Malaysia, Fac Elect Engn, Skudai 81310, Johor, Malaysia

[2] Univ Teknol Malaysia, Fac Biosceinces & Med Engn, Skudai 81310, Johor, Malaysia

[3] Univ Teknol Malaysia, Fac Mech Engn, Skudai 81310, Johor, Malaysia

来源：

MECHANICAL AND MATERIALS ENGINEERING | 2014年 / 554卷

关键词：

Electrical Discharge Machining; Pulse Power Generator; Gap Current; Gap Voltage;

D O I：

10.4028/www.scientific.net/AMM.554.643

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

Electrical Discharge Machining (EDM) is a advanced machine that can control electrical spark to erode metal on the workpiece. In manufacturing, EDM is used on hard material parts that are extremely difficult to machine by conventional machining processes. EDM system consists of a shaped tool and the work piece, which are connected to a power supply and placed in a dielectric fluid. EDM pulse power generator applies voltage and current pulses between the electrode and workpiece to generate sparks through the gap. To obtain the optimum metarial removal rate (MRR), a good alternative is to improve the gap voltage and gap current. A proposed solution to these issue is combining ultracapacitor bank to the main power supply circuit for EDM machines. The control feedback of this research is designed to make sure that the current on DC bus is maintained at current setting during the machining processes.

引用

页码：643 / +

页数：2

共 50 条

[1] Model of Pulse Power Generator in Electrical Discharge Machining (EDM) System
Ade Erawan, Minhat
Azli, Yahya
Nor Hisham, Khamis
Ahmad Saudi, Samosir
Muhammad Arif, Abdul Rahim
Trias, Andromeda
Kartiko, Nugroho
[J]. MECHANICAL AND MATERIALS ENGINEERING, 2014, 554 : 613 - +
[2] Power Generator of Electrical Discharge Machining (EDM) System
Ade Erawan, Minhat
Azli, Yahya
Nor Hisham, Khamis
Syahrullail, Samion
Zurkarmawan, Abu Bakar
Trias, Andromeda
[J]. MECHANICAL AND MATERIALS ENGINEERING, 2014, 554 : 638 - +
[3] One-Cycle Control for Pulse Power Generator in Electrical-Discharge-Machining
Yang, Fei
Liu, Yayun
Liu, Weihan
Yao, Kai
[J]. AMERICAN JOURNAL OF CLINICAL NUTRITION, 2021, : 11012 - 11022
[4] One-Cycle Control for Pulse Power Generator in Electrical-Discharge-Machining
Yang, Fei
Liu, Yayun
Liu, Weihan
Yao, Kai
[J]. IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, 2022, 69 (11) : 11012 - 11022
[5] Analysis and Control of Electrical Discharge Machining (EDM) Process
Zhou, Ming
Han, Fuzhu
Meng, Xianyi
Chen, Baojiang
[J]. 2009 IEEE INTERNATIONAL CONFERENCE ON INDUSTRIAL ENGINEERING AND ENGINEERING MANAGEMENT, VOLS 1-4, 2009, : 164 - 168
[6] Current type of electrical discharge machining pulse generator
Song, B.Y.
Zhao, W.S.
Shao, G.L.
[J]. Zhongguo Jixie Gongcheng/China Mechanical Engineering, 2001, 12 (04):
[7] Adaptive Voltage Position Control for Pulse Power Supply in Electrical Discharge Machining
Yang, Fei
Yang, Jiao
Yao, Kai
Hua, Han
[J]. IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, 2019, 66 (08) : 5895 - 5906
[8] Design and fabrication of control system-based ISO pulse generator for electrical discharge machining
Muthuramalingam, T.
Mohan, B.
[J]. International Journal of Mechatronics and Manufacturing Systems, 2013, 6 (02) : 133 - 143
[9] A study on improving machining characteristics of electrical discharge machining with modified transistor pulse generator
[J]. Muthuramalingam, T. (muthu1060@gmail.com), 2013, Inderscience Publishers, 29, route de Pre-Bois, Case Postale 856, CH-1215 Geneva 15, CH-1215, Switzerland (27) : 1 - 3
[10] Pulse generator for obtaining surfaces of small dimensions by electrical discharge machining
Coteata, Margareta
Floca, Alexandru
Dodun, Oana
Ionescu, Nicolae
Nagit, Gheorghe
Slatineanu, Laurentiu
[J]. 18TH CIRP CONFERENCE ON ELECTRO PHYSICAL AND CHEMICAL MACHINING (ISEM XVIII), 2016, 42 : 715 - 720

← 1 2 3 4 5 →