Improving metal-ceramic systems subjected to sliding contact by reinforcing the metallic counterpart with ceramic particles

被引：6

作者：

Kan, Wen Hao ^{[1
,2
,3
,4
]}

Huang, Siyu ^{[1
]}

Proust, Gwenaelle ^{[5
]}

Bhatia, Vijay ^{[2
]}

Chang, Li ^{[1
]}

Lucey, Timothy ^{[6
]}

Tang, Xinhu ^{[6
]}

Cairney, Julie M. ^{[1
,2
]}

机构：

[1] Univ Sydney, Sch Aerosp Mech & Mechatron Engn, Sydney, NSW 2006, Australia

[2] Univ Sydney, Australian Ctr Microscopy & Microanal, Sydney, NSW 2006, Australia

[3] Monash Ctr Addit Mfg, Notting Hill, Vic 3168, Australia

[4] Monash Univ, Dept Mat Sci & Engn, Clayton, Vic 3800, Australia

[5] Univ Sydney, Sch Civil Engn, Sydney, NSW 2006, Australia

[6] Weir Minerals Australia, Artarmon, NSW 2064, Australia

来源：

WEAR | 2020年 / 452卷

基金：

澳大利亚研究理事会;

关键词：

Sliding wear; Stainless steel; Metal-matrix composite; Bearings; Advanced ceramics; WEAR BEHAVIOR; SILICON-NITRIDE; TRIBOLOGICAL BEHAVIOR; STEEL; MICROSTRUCTURE; MECHANISMS; FRICTION; ZIRCONIA; ALUMINA;

D O I：

10.1016/j.wear.2020.203311

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

The study of sliding wear is important as it occurs in many industrial mechanical systems. In metal-ceramic sliding wear, reinforcing the metallic counterpart with ceramic particles transforms the system from a pure metal-ceramic interaction to one that contains both metal-ceramic and ceramic-ceramic interactions, which may improve the wear performance of both materials involved. This study shows that incorporating NbC particles into a bearing stainless steel reduces its wear rate against SiC, WC and Al2O3 counterparts but its wear rate remained unchanged against ZrO2. For the ceramic counterparts, SiC and WC also experienced reduced wear while Al2O3 showed negligible wear across all tests. ZrO2, on the other hand, experienced a very high level of wear when the stainless steel contained 5 vol% NbC but the wear rate gradually decreased as the volume fraction of NbC increased to 15 vol%. Higher NbC volume fractions are thus expected to yield further improvement.

引用

页数：13

共 50 条

[1] METAL-CERAMIC INTERACTIONS .3. SURFACE TENSION AND WETTABILITY OF METAL-CERAMIC SYSTEMS
HUMENIK, M
KINGERY, WD
JOURNAL OF THE AMERICAN CERAMIC SOCIETY, 1954, 37 (01) : 18 - 23
[2] Joining technology in metal-ceramic systems
Passerone, A
Muolo, ML
MATERIALS AND MANUFACTURING PROCESSES, 2000, 15 (05) : 631 - 648
[3] INTERFACIAL PHENOMENA IN METAL-CERAMIC SYSTEMS
PASSERONE, A
MATERIALS CHEMISTRY AND PHYSICS, 1986, 15 (3-4) : 263 - 279
[4] Focus Issue: Metal-Ceramic Systems
Lawley, Alan
INTERNATIONAL JOURNAL OF POWDER METALLURGY, 2011, 47 (02): : 2 - 2
[5] WEAR IN CERAMIC CERAMIC AND CERAMIC METAL RECIPROCATING SLIDING CONTACT .1.
ARONOV, V
MESYEF, T
JOURNAL OF TRIBOLOGY-TRANSACTIONS OF THE ASME, 1986, 108 (01): : 16 - 21
[6] Improving contact resistance in metal-ceramic heat exchangers running liquid metal by additive manufacturing and ceramic tubes with electroplated films
Armen, Jerald
Bruck, Hugh A.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2021, 113 (7-8): : 2101 - 2119
[7] Preparation of metal-ceramic composites by sonochemical synthesis of metallic nano-particles and in-situ decoration on ceramic powders
Poulia, A.
Sakkas, P. M.
Kanellopoulou, D. G.
Sourkouni, G.
Legros, C.
Argirusis, Chr.
ULTRASONICS SONOCHEMISTRY, 2016, 31 : 417 - 422
[8] THE FRICTION AND WEAR OF CERAMIC-CERAMIC AND CERAMIC-METAL COMBINATIONS IN SLIDING CONTACT
SLINEY, HE
DELLACORTE, C
LUBRICATION ENGINEERING, 1994, 50 (07): : 571 - 576
[9] Model systems for metal-ceramic interface studies
Wagner, M
Wagner, T
Carroll, DL
Marien, J
Bonnell, DA
Ruhle, M
MRS BULLETIN, 1997, 22 (08) : 42 - 48
[10] INFLUENCE OF GEOMETRY ON INCOMPATIBILITY IN METAL-CERAMIC SYSTEMS
DEHOFF, PH
ANUSAVICE, KJ
JOURNAL OF DENTAL RESEARCH, 1986, 65 : 217 - 217

← 1 2 3 4 5 →