High bandwidth thermal microscopy of machining AISI 1045 steel

被引：31
|
作者：
Davies, MA [1 ]
Cooke, AL [1 ]
Larsen, ER [1 ]
机构：
[1] Univ N Carolina, Ctr Precis Metrol, Dept Mech Engn & Engng Sci, Charlotte, NC 28223 USA
来源：
CIRP ANNALS-MANUFACTURING TECHNOLOGY | 2005年 / 54卷 / 01期
关键词：
high-speed cutting; finite element method; thermal microscope;
D O I：
10.1016/S0007-8506(07)60050-X
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
A custom thermal microscope was constructed using a high-bandwidth thermal imaging system (40 megapixels/sec). The microscope was attached to a high-speed machining centre (20 thousand RPM/18.5 kW spindle) that was operated as a high-speed lathe to measure temperature distributions during orthogonal cutting of AISI 1045 steel at surface speeds of up to 605 m/min. Measurements were made for a wide range of cutting parameters and compared with finite element analysis. While the ultimate goal is to produce improved tool design, the results emphasize the need for predictive rather than interpretive simulation of the temperature fields in machining.
引用
收藏
页码：63 / 66
页数：4
相关论文
共 50 条
  • [1] Material behaviour of aluminium 7075 and AISI 1045 steel in high speed machining
    Siems, S
    Dollmeier, R
    Warnecke, G
    TRANSACTIONS OF THE NORTH AMERICAN MANUFACTURING RESEARCH INSTITUTE OF SME, VOL XXVIII, 2000, 2000, : 101 - 106
  • [2] Evaluation of an Analytical Model in the Prediction of Machining Temperature of AISI 1045 Steel and AISI 4340 Steel
    Ning, Jinqiang
    Liang, Steven Y.
    JOURNAL OF MANUFACTURING AND MATERIALS PROCESSING, 2018, 2 (04):
  • [3] Chip control in the dry machining of hardened AISI 1045 steel
    Zhang, X. P.
    Wu, S. B.
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2017, 88 (9-12): : 3319 - 3327
  • [4] On the measurement and prediction of temperature fields in machining AISI 1045 steel
    Davies, MA
    Cao, Q
    Cooke, AL
    Ivester, R
    CIRP ANNALS-MANUFACTURING TECHNOLOGY, 2003, 52 (01) : 77 - 80
  • [5] ON THE IDENTIFICATION CONDITIONS OF A CONSTITUTIVE MODEL IN MACHINING OF AISI 1045 STEEL
    Courbon, C.
    Mabrouki, T.
    Rech, J.
    Rigal, J. -F.
    Mazuyer, D.
    D'Eramo, E.
    Daguier, P.
    INTERNATIONAL JOURNAL OF MATERIAL FORMING, 2010, 3 : 439 - 442
  • [6] On the identification conditions of a constitutive model in machining of AISI 1045 steel
    C. Courbon
    T. Mabrouki
    J. Rech
    J.-F. Rigal
    D. Mazuyer
    E. D’Eramo
    P. Daguier
    International Journal of Material Forming, 2010, 3 : 439 - 442
  • [7] Chip control in the dry machining of hardened AISI 1045 steel
    X. P. Zhang
    S. B. Wu
    The International Journal of Advanced Manufacturing Technology, 2017, 88 : 3319 - 3327
  • [8] Investigation of the Effects of Microgrooved Cutting Tool in High Speed Machining of AISI 1045 Steel
    Chen, Xingbang
    Duong, Nick H.
    Ma, J.
    Lei, Shuting
    PROCEEDINGS OF THE ASME 12TH INTERNATIONAL MANUFACTURING SCIENCE AND ENGINEERING CONFERENCE - 2017, VOL 1, 2017,
  • [9] Modelling the peak cutting temperature during high-speed machining of AISI 1045 steel
    Burns, T. J. (timothy.burns@nist.gov), 1600, Polish Academy of Sciences (60):
  • [10] Assessment of the Performance of Microbumped Cutting Tool in Machining of AISI 1045 Steel
    Ma, J.
    Duong, Nick H.
    Lei, Shuting
    PROCEEDINGS OF THE ASME INTERNATIONAL MECHANICAL ENGINEERING CONGRESS AND EXPOSITION, 2014, VOL 2B, 2014,
12345