Effect of nitrogen content on physical properties of glass fiber reinforced polyamide 6 prepared by microcellular injection molding

被引：8

作者：

Sykutera, Dariusz ^{[1
]}

Szewczykowski, Piotr ^{[1
]}

Roch, Mateusz ^{[1
]}

Wajer, Lukasz ^{[1
]}

Grabowski, Marek ^{[2
]}

Bielinski, Marek ^{[1
]}

机构：

[1] UTP Univ Sci & Technol, Inst Mfg Technol, Dept Mat Engn & Polymer Proc, Al Prof S Kaliskiego 7, PL-85796 Bydgoszcz, Poland

[2] GRAFORM Co, Wroblowa 7, PL-85437 Bydgoszcz, Poland

来源：

POLIMERY | 2018年 / 63卷 / 11-12期

关键词：

microcellular injection molding; MuCell (R) technology; polyamide PA6 GF30; porous materials; mechanical properties; MOLDED PARTS; BLOWING AGENTS; POLYPROPYLENE; TECHNOLOGY; MUCELL(R); FOAMS;

D O I：

10.14314/polimery.2018.11.1

中图分类号：

O63 [高分子化学（高聚物）];

学科分类号：

070305 ; 080501 ; 081704 ;

摘要：

The aim of the study was to determine the effect of the amount of nitrogen dosed in supercritical state to polymer melt on structure and physical properties of large-scale molded pieces from polyamide PA6 GF30, obtained in the process of microcellular injection molding with gas dosage using MuCell (R) method. Apart from the reduction of the density at a level of about 15 % for samples with the highest nitrogen content, the increase of the impact resistance of samples PA6 GF30 was observed. The other investigated mechanical properties were maintained at a good level.

引用

页码：743 / 749

页数：7

共 50 条

[21] GLASS REINFORCED 66 NYLON - EFFECT OF MOLDING VARIABLES ON FIBER LENGTH AND RELATION OF FIBER LENGTH TO PHYSICAL PROPERTIES
FILBERT, WC
SPE JOURNAL, 1968, 24 (04): : 37 - &
[22] The effect of electron beam irradiation on properties of virgin and glass fiber-reinforced polyamide 6
Porubska, Maria
Janigova, Ivica
Jomova, Klaudia
Chodak, Ivan
RADIATION PHYSICS AND CHEMISTRY, 2014, 102 : 159 - 166
[23] Effect of compounding conditions on mechanical properties of glass fiber-reinforced polyamide-6
Nagae, S
Nagura, K
Yamagiwa, N
Yamane, Y
Miyake, K
Inoue, K
INTERNATIONAL POLYMER PROCESSING, 1997, 12 (02) : 116 - 122
[24] Effect of Compounding Conditions on Mechanical Properties of Glass Fiber-Reinforced Polyamide-6
Nagae, S.
Nagura, K.
Yamagiwa, N.
Yamane, Y.
International Polymer Processing, 12 (02):
[25] The effect of injection molding process parameters on the tensile properties of short glass fiber-reinforced PBT
Fung, CP
Hwang, JR
Hsu, CC
POLYMER-PLASTICS TECHNOLOGY AND ENGINEERING, 2003, 42 (01) : 45 - 63
[26] MECHANICAL PROPERTIES OF GLASS FIBER REINFORCED POLYOXYMETHYLENE COMPOSITES BY DIRECT FIBER FEEDING INJECTION MOLDING
Mathurosemontri, Suchalinee
Uawongsuwan, Putinun
Ichikawa, Hiroaki
Inoya, Hiroyuki
Hamada, Hiroyuki
PROCEEDINGS OF THE ASME INTERNATIONAL MECHANICAL ENGINEERING CONGRESS AND EXPOSITION, 2014, VOL 2A, 2014,
[27] Micro-machinability of injection molded polyamide 6 polymer and glass-fiber reinforced polyamide 6 composite
Kuram, Emel
COMPOSITES PART B-ENGINEERING, 2016, 88 : 85 - 100
[28] Mechanical and thermal properties of injection molded long glass fiber reinforced rubber toughened polyamide 6 composite
Lin, SH
Ma, CCM
Meng, HF
Perng, LH
MATERIALS SCIENCE RESEARCH INTERNATIONAL, 1996, 2 (02): : 87 - 92
[29] Effect of moisture on the mechanical properties of glass fiber reinforced polyamide composites
Chaichanawong, Jintawat
Thongchuea, Chanchai
Areerat, Surat
ADVANCED POWDER TECHNOLOGY, 2016, 27 (03) : 898 - 902
[30] Water assisted injection molding of glass fiber reinforced PA-6 composites
Liu, Shih-Jung
Shih, Chang-Chi
ABSTRACTS OF PAPERS OF THE AMERICAN CHEMICAL SOCIETY, 2007, 234

← 1 2 3 4 5 →