Bifurcation Characteristics of Emergency Extension of a Landing Gear Mechanism Considering Aerodynamic Effect

被引:2
|
作者
Yin, Yin [1 ]
Yang, Yixin [1 ]
Xu, Kui [1 ]
Nie, Hong [1 ]
Wei, Xiaohui [1 ]
机构
[1] Nanjing Univ Aeronaut & Astronaut, State Key Lab Mech & Control Mech Struct, Nanjing 210016, Peoples R China
基金
中国国家自然科学基金;
关键词
Landing gear; Emergency extension failure; Bifurcation analysis; Numerical continuation; Aerodynamic load; NUMERICAL CONTINUATION ANALYSIS; OPTIMIZATION; DESIGN; MODEL;
D O I
10.1061/(ASCE)AS.1943-5525.0001261
中图分类号
V [航空、航天];
学科分类号
08 ; 0825 ;
摘要
The emergency extension system for nose landing gear (NLG) is vitally important for safe landing in the event of hydraulic source failure. To study the dynamic properties of NLG emergency extension, it is necessary to explore the aerodynamic load in detail, which is a potential adverse factor that hinders the successful deployment of NLG. The emergency extension failure of a door-linkage NLG mechanism was studied from a novel bifurcation perspective in this paper. NLG models (excluding and including aerodynamic loads) formulating the mechanism as a series of steady-state constraint equations were derived. Solutions to these equations were continued numerically, and the NLG retraction-extension cycles in different models were compared. The critical condition for smooth extension was obtained based on the bifurcation analysis. The failure principle was explained, that is, the disappearance of bifurcation points characterizing the successful locking. The variations of bifurcation point as a function of spring parameters and door aerodynamic loads were investigated. An effective solution to the failure was put forward in which the unlocking force is reduced by 33.0%.
引用
收藏
页数:18
相关论文
共 47 条
  • [31] Investigation of vibration characteristics of gear-bearing transmission system considering the effect of profile shifted coefficient
    Wang, Hao
    Liu, Jie
    Zhao, Weiqiang
    JOURNAL OF LOW FREQUENCY NOISE VIBRATION AND ACTIVE CONTROL, 2023, 42 (04) : 1596 - 1615
  • [32] Generation mechanism and evolution of five-state meshing behavior of a spur gear system considering gear-tooth time-varying contact characteristics
    Jian-fei Shi
    Xiang-feng Gou
    Ling-yun Zhu
    Nonlinear Dynamics, 2021, 106 : 2035 - 2060
  • [33] Generation mechanism and evolution of five-state meshing behavior of a spur gear system considering gear-tooth time-varying contact characteristics
    Shi, Jian-fei
    Gou, Xiang-feng
    Zhu, Ling-yun
    NONLINEAR DYNAMICS, 2021, 106 (03) : 2035 - 2060
  • [34] A Numerical Study of the Wind Speed Effect on the Flow and Acoustic Characteristics of the Minor Cavity Structures in a Two-Wheel Landing Gear
    Huang, Longlong
    Zhao, Kun
    Liang, Junbiao
    Kopiev, Victor
    Belyaev, Ivan
    Zhang, Tian
    APPLIED SCIENCES-BASEL, 2021, 11 (23):
  • [35] Study on the water characteristics and microscopic mechanism of compacted silt considering the effect of stress
    Li, Yonghui
    Han, Feiyang
    Sun, Liqin
    Li, Xin
    BULLETIN OF ENGINEERING GEOLOGY AND THE ENVIRONMENT, 2024, 83 (01)
  • [36] Study on the water characteristics and microscopic mechanism of compacted silt considering the effect of stress
    Yonghui Li
    Feiyang Han
    Liqin Sun
    Xin Li
    Bulletin of Engineering Geology and the Environment, 2024, 83
  • [37] Effect mechanism of cooling delta aerodynamic field equalizing on the cooling characteristics of dry cooling tower
    Zhao, Yuanbin
    Zhao, Qian
    Li, Fei
    Liang, Qinghe
    Li, Xuan
    Chen, Yasi
    INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER, 2023, 148
  • [38] An Experimental and Numerical Investigation of the Characteristics and Mechanism of Spacing Cracks in Loess Considering the Size Effect
    Wei, Xin
    Zhou, Yunru
    Chen, Xuanyi
    SUSTAINABILITY, 2023, 15 (16)
  • [39] Thermal characteristics testing and thermal error modeling on a worm gear grinding machine considering cutting fluid thermal effect
    Xiaojun Shi
    Weiku Wang
    Yingjie Mu
    Xiao Yang
    The International Journal of Advanced Manufacturing Technology, 2019, 103 : 4317 - 4329
  • [40] Selection of Motors and Gear Reducers for Four-Axis Palletizing Robots Considering the Motion Characteristics and Dynamic Coupling Effect
    Park, Il Hwan
    Hong, Dae Sun
    INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING, 2023, 24 (12) : 2269 - 2278