Application of Load-pull in Power Amplifier Design

被引：1
|
作者：
Li, Xiaoguang [1 ]
Bai, Xuchan [1 ]
Yuan, Qiang [2 ]
Zhang, Songan [3 ]
机构：
[1] Luoyang Inst Sci & Technol, Dept Elect Engn & Automat, Luoyang 471023, Peoples R China
[2] Luoyang Urban Planning & Architecture Design Res, Luoyang 471023, Peoples R China
[3] SCIVIC Engn Corp, Environm Protect & Energy Saving Dept, Luoyang 471023, Peoples R China
来源：
3RD INTERNATIONAL CONFERENCE ON APPLIED ENGINEERING | 2016年 / 51卷
关键词：
Power amplifiers;
D O I：
10.3303/CET1651056
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
Aiming at parasitic effect physical design of the power amplifier, according to the load-pull result of input and output impedance by the conjugate match, a wideband high efficiency method of power amplifier was proposed basing on the momentum technology and load-pull method in this paper after using the ADS software. To realize high efficiency, matching circuit is applied to the amplifier to reduce the chip size, which are changed into corresponding momentum components and re-used in schematic design with well improvement design accuracy are designed by the conjugate match method basing on the analysis of unconditional stability, as well as to realize the optimum impedances over a wide bandwidth for high efficiency at each stage. The simulation results showed that the new method could get the optimal output within three iterations, which verified that the new method is a practical and efficient in power amplifier design.
引用
收藏
页码：331 / 336
页数：6
相关论文
共 50 条
  • [21] Inverse Active Load-Pull in an Inverse Doherty Amplifier
    Hone, Thomas M.
    Bensmida, Souheil
    Morris, Kevin A.
    Beach, Mark A.
    McGeehan, Joe P.
    Lees, Jonathan
    Benedikt, Johannes
    Tasker, Paul J.
    2013 IEEE TOPICAL CONFERENCE ON POWER AMPLIFIERS FOR WIRELESS AND RADIO APPLICATIONS (PAWR), 2013, : 4 - 6
  • [22] HIGH-POWER MILLIMETER-WAVE MMIC AMPLIFIER DESIGN USING IMPROVED LOAD-PULL METHOD
    NAGATOMO, K
    KOIKE, S
    OKUBO, N
    SHIGAKI, M
    IEICE TRANSACTIONS ON ELECTRONICS, 1992, E75C (06) : 663 - 668
  • [23] A 5-9 GHz CMOS Ultra-wideband Power Amplifier Design Using Load-Pull
    Mosalam, H.
    Allam, A.
    Jia, H.
    Pokharel, R.
    Ragab, M.
    Yoshida, K.
    2013 IEEE 20TH INTERNATIONAL CONFERENCE ON ELECTRONICS, CIRCUITS, AND SYSTEMS (ICECS), 2013, : 13 - 16
  • [24] Sequential Load-Pull Technique for Multioctave Design of RF Power Amplifiers
    Taghavi, H.
    Akbarpour, M. H.
    Ghannouchi, F. M.
    IEEE TRANSACTIONS ON CIRCUITS AND SYSTEMS II-EXPRESS BRIEFS, 2016, 63 (09) : 818 - 822
  • [25] Improvement to Load-pull Technique for Design of Large-signal Amplifier in K band
    Moravek, Ondrej
    Hoffmann, Karel
    RADIOENGINEERING, 2011, 20 (04) : 828 - 831
  • [26] Verifying power load-pull test systems
    不详
    MICROWAVES & RF, 2005, 44 (02) : 88 - 88
  • [27] A Doherty Amplifier With Modified Load Modulation Scheme Based on Load-Pull Data
    Nguyen, Duy P.
    Curtis, Jeffery
    Anh-Vu Pham
    IEEE TRANSACTIONS ON MICROWAVE THEORY AND TECHNIQUES, 2018, 66 (01) : 227 - 236
  • [28] High efficiency power amplifier - Distributed amplifier topology and non-uniform load-pull (NLP) power combining technique
    Man, Hung Kwok
    Mung, Steve W. Y.
    Shing, Chan Wing
    HKIE Transactions Hong Kong Institution of Engineers, 2010, 17 (04): : 49 - 54
  • [29] A simple and effective load-pull system for RF power transistor large-signal measurements for wireless communication power amplifier design
    Chiang, CY
    Chuang, HR
    IEEE TRANSACTIONS ON INSTRUMENTATION AND MEASUREMENT, 1997, 46 (05) : 1150 - 1155
  • [30] High-efficiency load-pull harmonic controlled class-E power amplifier
    Ortega-Gonzalez, J
    Jimenez-Martin, JL
    Asensio-Lopez, A
    Torregrosa-Penalva, G
    IEEE MICROWAVE AND GUIDED WAVE LETTERS, 1998, 8 (10): : 348 - 350
12345