Deformation analysis of short glass fiber-reinforced polypropylene injection-molded plastic parts

被引：10
|
作者：
Siklo, B. [1 ]
Cameron, K. [2 ]
Kovacs, J. G. [1 ]
机构：
[1] Budapest Univ Technol & Econ, Dept Polymer Engn, H-1111 Budapest, Hungary
[2] Univ W Scotland, Edinburgh, Midlothian, Scotland
来源：
JOURNAL OF REINFORCED PLASTICS AND COMPOSITES | 2011年 / 30卷 / 16期
关键词：
warpage; corner effect; injection molding; deformation; injection mold; mold temperature; MECHANICAL-PROPERTIES; MOLDING PROCESS; WARPAGE; SHRINKAGE; PREDICTION; PARAMETERS; SIMULATION; STRESSES;
D O I：
10.1177/0731684411426203
中图分类号：
TB33 [复合材料];
学科分类号：
摘要：
The warpage of injection-molded plastic parts is a complex problem being affected by different technological parameters, material properties, and mold design. Hence, the description of the deformation is difficult as well. This article presents the effect of fiber content and mold temperature difference on the deformation of polypropylene parts. Based on the measurement results, a linear approximation and a calculation method are shown, which can be used to jointly determine the ideal fiber content and mold temperature difference to produce undeformed plastic parts.
引用
收藏
页码：1367 / 1372
页数：6
相关论文
共 50 条
  • [21] Effect of screw design on fiber breakage and dispersion in injection-molded long glass-fiber-reinforced polypropylene
    Inoue, Akira
    Morita, Kazuya
    Tanaka, Tatsuya
    Arao, Yoshihiko
    Sawada, Yasutake
    JOURNAL OF COMPOSITE MATERIALS, 2015, 49 (01) : 75 - 84
  • [22] PERILS OF PROTOTYPES FOR INJECTION-MOLDED PLASTIC PARTS
    CHASTAIN, CE
    MACHINE DESIGN, 1973, 45 (27) : 137 - 141
  • [23] Experimental and numerical investigations on formation mechanisms of hollow structures in overflow water-assisted injection-molded parts of short-glass-fiber-reinforced polypropylene
    Jiang, Qingsong
    Zhang, Wei
    Wan, Zhihui
    Zhou, Haiying
    Jiang, Shiyu
    Nie, Huarong
    JOURNAL OF APPLIED POLYMER SCIENCE, 2024, 141 (36)
  • [24] Warpage of injection-molded automotive B pillar trim fabricated with ramie fiber-reinforced polypropylene composites
    Chen, Dachuan
    Lu, Gang
    He, Liping
    Li, Wenjun
    Yuan, Jianmin
    JOURNAL OF REINFORCED PLASTICS AND COMPOSITES, 2015, 34 (14) : 1144 - 1152
  • [25] Effect of fiber content on the layer structure formation of fibers inside injection-molded products using short glass fiber-reinforced materials
    Hamanaka, Senji
    Nonomura, Chisato
    Thanh Binh Nguyen Thi
    Yokoyama, Atsushi
    JOURNAL OF POLYMER ENGINEERING, 2021, 41 (03) : 235 - 243
  • [26] Mechanical Characterization of Frontal and Flowing Weld Lines in Injection-molded Short Fiber-reinforced Thermoplastics
    Baradi, M. B.
    Cruz, C.
    Regnier, G.
    PROCEEDINGS OF THE EUROPE/AFRICA CONFERENCE DRESDEN 2017 - POLYMER PROCESSING SOCIETY PPS, 2019, 2055
  • [27] Mechanical and microstructural characterization of flowing weld lines in injection-molded short fiber-reinforced PBT
    Baradi, Mohamed Besher
    Cruz, Camilo
    Riedel, Thomas
    Regnier, Gilles
    POLYMER TESTING, 2019, 74 : 152 - 162
  • [28] COMPARISON OF THE FAILURE MODE IN SHORT AND LONG GLASS-FIBER-REINFORCED INJECTION-MOLDED POLYPROPYLENE COMPOSITES BY ACOUSTIC-EMISSION
    CZIGANY, T
    KARGERKOCSIS, J
    POLYMER BULLETIN, 1993, 31 (04) : 495 - 501
  • [29] Tensile, impact and fiber length properties of injection-molded short and long glass fiber-reinforced polyamide 6,6 composites
    Hassan, A
    Yahya, R
    Yahaya, AH
    Tahir, ARM
    Hornsby, PR
    JOURNAL OF REINFORCED PLASTICS AND COMPOSITES, 2004, 23 (09) : 969 - 986
  • [30] Loading rate and temperature dependence of flexural behavior in injection-molded glass fiber reinforced polypropylene composites
    Yu, Lichao
    Ma, Yan
    COMPOSITES PART B-ENGINEERING, 2019, 161 : 285 - 299
12345