Influence of cutting tool stiffness on edge formability

被引:3
|
作者
Levin, E. [1 ]
Larour, P. [2 ]
Heuse, M. [3 ]
Staupendahl, D. [1 ]
Clausmeyer, T. [1 ]
Tekkaya, A. E. [1 ]
机构
[1] TU Dortmund Univ, Inst Forming Technol & Lightweight Components, Baroper Str 303, D-44227 Dortmund, Germany
[2] Voestalpine Stahl GmbH, Voestalpine Str 3, A-4020 Linz, Austria
[3] Faurecia Autositze GmbH, Nordsehler Str 38, D-31655 Stadthagen, Germany
关键词
DIE;
D O I
10.1088/1757-899X/418/1/012061
中图分类号
TH [机械、仪表工业];
学科分类号
0802 ;
摘要
For the evaluation of the forming behaviour of cut edges of AHSS the Hole Expansion Test (HET) standardized in the ISO 16630 is generally used. However, the observed Hole Expansion Ratio (HER) is prone to significant scatter. One reason for this scatter is the subjective observation of the through thickness crack by the machine operator. Additionally, the ISO is not very specific in its description of the test setup and material preparation, actually allowing great variations in the cutting process. Although the nominal cutting clearance is specified, a low stiffness of the punching machine or tool can cause a non-uniform clearance along the circumference. Additionally, an oblique position of the punch can cause an angled or eccentric sheared hole, resulting in additional crack initiation sites on the shear cut surface. FE simulations are used to investigate the stiffness effects of a C-frame press design. A comparative round robin analysis based on IS016630 was performed by cross-testing both cutting and hole expansion setups for a high strength hot rolled steel grade. Significant differences were registered in the HER values, whereby the cutting process was identified to have the largest influence on HER variation. The homogeneity of the burnished zone along the circumference was observed to give valuable information about the cut edge quality and subsequent level of HER values.
引用
收藏
页数:8
相关论文
共 50 条
  • [1] Influence of Edge Preparation on Cutting Tool Wear
    Chai, Guobing
    Wang, Wei
    Yu, Aibing
    [J]. ADVANCES IN ENGINEERING DESIGN AND OPTIMIZATION III, PTS 1 AND 2, 2012, 201-202 : 1178 - 1181
  • [2] Influence of the Cutting Edge Radius and the Cutting Edge Preparation on Tool Life and Cutting Forces at Inserts with Wiper Geometry
    Fulemova, Jaroslava
    Janda, Zdenek
    [J]. 24TH DAAAM INTERNATIONAL SYMPOSIUM ON INTELLIGENT MANUFACTURING AND AUTOMATION, 2013, 2014, 69 : 565 - 573
  • [3] THE INFLUENCE OF TOOL STIFFNESS OF THE LIFETIME OF THE INSERTS IN INTERRUPTED CUTTING OPERATIONS
    MASNATA, A
    RUISI, VF
    [J]. CURRENT ADVANCES IN MECHANICAL DESIGN & PRODUCTION IV, 1989, : 545 - 551
  • [4] Influence of Cutting Process on the Flanging Formability of the Cut Edge for DP980 Steel
    Chang, Ying
    Zhang, Jiarui
    Han, Shuo
    Li, Xiaodong
    Yu, Shuzhou
    [J]. METALS, 2023, 13 (05)
  • [5] Influence of cutting edge radius of coated tool in orthogonal cutting of alloy steel
    Rech, J
    Yen, YC
    Hamdi, H
    Altan, T
    Bouzakis, KD
    [J]. MATERIALS PROCESSING AND DESIGN: MODELING, SIMULATION AND APPLICATIONS, PTS 1 AND 2, 2004, 712 : 1402 - 1407
  • [6] Influence of cutting-edge radius by an edge-honing process on the cutting tool life and coating
    Kwak, Yein
    Bae, Yeung Ho
    Kurniawan, Rendi
    Chen, Jielin
    Xu, Moran
    Saood, Ali
    Ko, Tae Jo
    [J]. Journal of Mechanical Science and Technology, 2024, 38 (10) : 5595 - 5604
  • [7] Influence of thermal and mechanical shocks to cutting edge tool life
    Cep, Robert
    Ocenasova, Lenka
    Novakova, Jana
    Kouril, Karel
    Valicek, Jan
    Barisic, Branimir
    [J]. World Academy of Science, Engineering and Technology, 2009, 56 : 292 - 295
  • [8] Influence of the tool edge geometry on specific cutting energy at high-speed cutting
    Rodrigues, Alessandro R.
    Coelho, Reginaldo T.
    [J]. JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING, 2007, 29 (03) : 279 - 283
  • [9] THE CUTTING EDGE OF TOOL LIFE
    GILMORE, RC
    [J]. WOOD & WOOD PRODUCTS, 1985, 90 (07): : 59 - 60
  • [10] The Cutting Edge on Tool Coatings
    Cannell, Thom
    [J]. MANUFACTURING ENGINEERING, 2023, 170 (01): : 53 - 59