A study on the effects of vibrations on the surface finish using a surface topography simulation model for turning

被引：101
|
作者：
Lin, SC [1 ]
Chang, MF [1 ]
机构：
[1] Natl Tsing Hua Univ, Dept Power Mech Engn, Hsinchu 30043, Taiwan
来源：
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE | 1998年 / 38卷 / 07期
关键词：
turning; vibrations; surface roughness;
D O I：
10.1016/S0890-6955(97)00073-4
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
In this paper, a surface topography simulation model is established to simulate the surface finish profile generated after a turning operation. The surface topography simulation model incorporates the effects of the relative motion between the cutting tool and the workpiece with the effects of tool geometry to simulate the resultant surface geometry. It is experimentally shown that the surface topography simulation model can properly simulate the surface profile generated by turning operations. The surface topography simulation model is used to study the effects of vibrations on the surface finish profile. It is found that the vibration frequency ratio is a more important vibration parameter than the vibration frequency on the characterization of the surface finish profile. The vibration frequency ratio is the ratio between the vibration frequency and the spindle rotational speed. (C) 1998 Elsevier Science Ltd. All rights reserved.
引用
收藏
页码：763 / 782
页数：20
相关论文
共 50 条
  • [31] Research of surface finish during titanium alloy turning
    Zebala, Wojciech
    Gawlik, Jozef
    Matras, Andrzej
    Struzikiewicz, Grzegorz
    Slusarczyk, Lukasz
    PRECISION MACHINING VII, 2014, 581 : 409 - 414
  • [32] SURFACE-FINISH MEASUREMENTS IN TURNING AND THEIR MATHEMATICAL INTERPRETATION
    JONA, MG
    MECHANICAL ENGINEERING, 1968, 90 (01) : 62 - &
  • [33] SURFACE FINISH PRODUCED BY A VIBRATING TOOL DURING TURNING
    SKELTON, RC
    INTERNATIONAL JOURNAL OF MACHINE TOOL DESIGN AND RESEARCH, 1969, 9 (04): : 375 - &
  • [34] SOME ASPECTS OF WORKPIECE SURFACE FINISH DURING TURNING
    BANERJEE, JK
    MICROTECNIC, 1978, (04): : 27 - 29
  • [35] Optimization of energy consumption and surface quality in finish turning
    Guo, Yansong
    Loenders, Jef
    Duflou, Joost
    Lauwers, Bert
    FIFTH CIRP CONFERENCE ON HIGH PERFORMANCE CUTTING 2012, 2012, 1 : 512 - 517
  • [36] An Expert System for the Prediction of Surface Finish in Turning Process
    U S Dixit
    K Acharyya
    A D Sahasrabudhe
    厦门大学学报(自然科学版), 2002, (S1) : 191 - 191
  • [37] Analysis of tool wear and surface finish in hard turning
    T. Tamizharasan
    T. Selvaraj
    A. Noorul Haq
    The International Journal of Advanced Manufacturing Technology, 2006, 28 : 671 - 679
  • [38] Effect of wedge angle on surface roughness in finish turning: analytical and experimental study
    Sung, A. N.
    Ratnam, M. M.
    Loh, W. P.
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2014, 74 (1-4): : 139 - 150
  • [39] Hard turning: Parametric optimization using genetic algorithm for rough/finish machining and study of surface morphology
    Batish, Ajay
    Bhattacharya, Anirban
    Kaur, Manwinder
    Cheema, Manjot Singh
    JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY, 2014, 28 (05) : 1629 - 1640
  • [40] Effect of wedge angle on surface roughness in finish turning: analytical and experimental study
    A. N. Sung
    M. M. Ratnam
    W. P. Loh
    The International Journal of Advanced Manufacturing Technology, 2014, 74 : 139 - 150
12345