Tool runout and single-edge cutting in micro-milling

被引：10
|
作者：
Zhang, Xiang [1 ]
Pan, Xudong [1 ]
Wang, Guanglin [1 ]
Zhou, Dong [1 ]
机构：
[1] Harbin Inst Technol, Sch Mechatron Engn, Harbin 150001, Heilongjiang, Peoples R China
来源：
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY | 2018年 / 96卷 / 1-4期
基金：
中国国家自然科学基金;
关键词：
Tool runout; Single edge cutting; Micro-milling; Criterion; END; MODEL; IDENTIFICATION; FORCES;
D O I：
10.1007/s00170-018-1620-y
中图分类号：
TP [自动化技术、计算机技术];
学科分类号：
0812 ;
摘要：
Micro-milling is a direct and effective manufacturing method for complex three-dimensional miniaturized parts. Since tool runout has a great influence on micro-milling, this paper proposes a simple and effective method for measuring tool runout parameters. The method was based on the displacement measurement, which obtained the tool runout length and tool runout angle by solving some equations related to the cutter parameters. After analyzing the cutting trajectories of the cutter, a single-edge cutting criterion in micro-milling was proposed. According to the single-edge cutting criterion, the influencing factors of single-edge cutting both in micro-side milling and micro-end milling were analyzed respectively. Finally, the influences of single-edge cutting on micro-milling were analyzed and the single-edge cutting phenomenon was verified by the experiment of cutting forces.
引用
收藏
页码：821 / 832
页数：12
相关论文
共 50 条
  • [11] Micro-milling tool wear monitoring under variable cutting parameters and runout using fast cutting force coefficient identification method
    Tongshun Liu
    Kunpeng Zhu
    Gang Wang
    The International Journal of Advanced Manufacturing Technology, 2020, 111 : 3175 - 3188
  • [12] Cutting force denoising in micro-milling tool condition monitoring
    Zhu, K.
    Hong, G. S.
    Wong, Y. S.
    Wang, W.
    INTERNATIONAL JOURNAL OF PRODUCTION RESEARCH, 2008, 46 (16) : 4391 - 4408
  • [13] Study on developing predicted system model of cutting-edge trajectory for micro-milling process based on tool runout error, chip thickness and force signal
    Sun, Yao
    Sun, Yirong
    Huang, Yiming
    Gong, Siqian
    Sun, Mingsheng
    Liu, Ming
    MECHANICAL SYSTEMS AND SIGNAL PROCESSING, 2025, 228
  • [14] Micro-milling force modeling with tool wear and runout effect by spatial analytic geometry
    Guochao Li
    Si Li
    Kunpeng Zhu
    The International Journal of Advanced Manufacturing Technology, 2020, 107 : 631 - 643
  • [15] Modeling and experimental study on the force of micro-milling titanium alloy based on tool runout
    Li, Guo
    Qu, Da
    Feng, Wei Wei
    Wang, Bo
    Li, Na
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2016, 87 (1-4): : 1193 - 1202
  • [16] Analysis of a single-edge micro cutting process in a hybrid parallel-serial machine tool
    Fajardo-Pruna, Marcelo
    Lopez-Estrada, Luis
    Perez, Hilde
    Diez, Eduardo
    Vizan, Antonio
    INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES, 2019, 151 : 222 - 235
  • [17] Investigation on dynamic tool deflection and runout-dependent analysis of the micro-milling process
    Wang, Dongqian
    Penter, Lars
    Haenel, Albrecht
    Yang, Yang
    Ihlenfeldt, Steffen
    MECHANICAL SYSTEMS AND SIGNAL PROCESSING, 2022, 178
  • [18] Micro-milling force modeling with tool wear and runout effect by spatial analytic geometry
    Li, Guochao
    Li, Si
    Zhu, Kunpeng
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2020, 107 (1-2): : 631 - 643
  • [19] Modeling and experimental study on the force of micro-milling titanium alloy based on tool runout
    Guo Li
    Da Qu
    Wei Wei Feng
    Bo Wang
    Na Li
    The International Journal of Advanced Manufacturing Technology, 2016, 87 : 1193 - 1202
  • [20] Modeling of cutting force in micro-milling considering asymmetric tool wear
    Wang, Weisu
    Tang, Yanling
    Guo, Xuhong
    Zhang, Kedong
    Liu, Tongshun
    Wang, Chengdong
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2024, 133 (3-4): : 1597 - 1608
12345