Optimization of the Inter-Operation Annealing of Cold-Drawn Eutectoid Steels

被引：0

作者：

Grygier, D. ^{[1
]}

Rutkowska-Gorczyca, M. ^{[1
]}

Zak, A. ^{[1
]}

Jasinski, R. ^{[1
]}

机构：

[1] Wroclaw Univ Technol, Dept Mat Sci Strength & Welding Technol, M Smoluchowskiego 25, PL-50372 Wroclaw, Poland

来源：

ACTA PHYSICA POLONICA A | 2016年 / 130卷 / 04期

关键词：

PEARLITIC STEEL; MECHANICAL-PROPERTIES; CARBON-STEEL; DEFORMATION; BEHAVIOR;

D O I：

10.12693/APhysPolA.130.931

中图分类号：

O4 [物理学];

学科分类号：

0702 ;

摘要：

The test of the results presented in this paper has demonstrated that the most suitable recrystallizing annealing temperature for cold drawn eutectoid steels is 700 degrees C. The microscopic examinations, with the use of scanning electron microscopy and transmission electron microscopy and the results of mechanical properties tests have shown that only at this temperature it is possible to obtain the fully recrystallized homogeneous fine-grained structure of the pearlitic steel.

引用

页码：931 / 934

页数：4

共 50 条

[31] Improvement in Performance of Cold-drawn SCM435 Alloy Steel Wires through Optimization of Intercritical Annealing Parameters
Yang, Chih-Cheng
Lu, Nan-Hua
SENSORS AND MATERIALS, 2019, 31 (11) : 3639 - 3654
[32] AN X-RAY INVESTIGATION OF INTERNAL STRAINS IN COLD-DRAWN STEELS .3.
BROOKES, PE
JOURNAL OF THE IRON AND STEEL INSTITUTE, 1950, 165 (04): : 370 - 374
[33] High-resolution multiscale modeling of mechanical behavior of cold-drawn pearlitic steels
Huang, Xutao
Wang, Jianjun
Zhao, Sixin
Yao, Zan
Liu, Chunming
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2021, 15 : 5920 - 5935
[34] TECHNOLOGICAL PROPERTIES OF COLD-DRAWN AND SUBSEQUENTLY HOT-DIP GALVANIZED PRESTRESSED STEELS
REHM, G
NURNBERGER, U
STAHL UND EISEN, 1978, 98 (12): : 399 - 402
[35] The effects of alloying elements on tensile strength and the occurrence of delamination in cold-drawn hyper-eutectoid steel wires
D. B. Park
J. W. Lee
Y. S. Lee
K. T. Park
W. J. Nam
Metals and Materials International, 2009, 15 : 197 - 202
[36] The Effects of Alloying Elements on Tensile Strength and the Occurrence of Delamination in Cold-Drawn Hyper-Eutectoid Steel Wires
Park, D. B.
Lee, J. W.
Lee, Y. S.
Park, K. T.
Nam, W. J.
METALS AND MATERIALS INTERNATIONAL, 2009, 15 (02) : 197 - 202
[37] Annealing twin formation and recrystallization study of cold-drawn copper wires from EBSD measurements
Baudin, T.
Etter, A. L.
Penelle, R.
MATERIALS CHARACTERIZATION, 2007, 58 (10) : 947 - 952
[38] Microstructural and Textural Evolution of Cold-Drawn Mg-Gd Wires during Annealing Treatment
Sun, Liuxia
Bai, Jing
Xue, Feng
Yan, Kai
MATERIALS, 2024, 17 (03)
[39] Effects of small additions of lead, sulphur and oxygen on annealing characteristics of cold-drawn pure copper
Aoyama, S
Kanno, M
JOURNAL OF MATERIALS SCIENCE, 1996, 31 (09) : 2393 - 2399
[40] Effect of thermo-mechanical treatments on mechanical properties and residual stresses in cold-drawn wire rods of eutectoid steel
Korchunov, A.
Polyakova, M.
Koptseva, N.
Brunelli, K.
Breda, M.
Dabala, M.
METALLURGIA ITALIANA, 2016, (02): : 5 - 11

← 1 2 3 4 5 →