Vapour Phase Soldering on Flexible Printed Circuit Boards

被引：0

作者：

Geczy, Attila ^{[1
]}

Batorfi, Reka ^{[1
]}

Szeles, Gergely ^{[1
]}

Luhaly, Adam ^{[1
]}

Ruszinko, Miklos ^{[1
]}

Berenyi, Richard ^{[1
]}

机构：

[1] Budapest Univ Technol & Econ, Dept Elect Technol, Budapest, Hungary

来源：

2014 IEEE 20TH INTERNATIONAL SYMPOSIUM FOR DESIGN AND TECHNOLOGY IN ELECTRONIC PACKAGING (SIITME) | 2014年

关键词：

Flexible; Printed Circuit Board; Vapour Phase Soldering; polyimide;

D O I：

暂无

中图分类号：

TM [电工技术]; TN [电子技术、通信技术];

学科分类号：

0808 ; 0809 ;

摘要：

The paper presents experimental results about Vapour Phase Soldering on flexible printed circuit boards, where the standard Surface Mounted Technology process was used for investigation. Test boards were prepared from FR4 type Printed Circuit Boards and single-sided flexible polyimide substrates. Lead-free SAC305 paste and different chip size surface mounted resistors were used for the test assembly. The soldering was performed with heat-level vapour phase method in a commercial oven. The tests were composed of different board setups: where the FR4 or the flexible boards were soldered without fixtures, and where the flexible boards were supported by fixtures. The results were evaluated with X-ray microscopy, cross-section optical inspection (IMC tests) and shear tests. The conclusion reveals similar quality factors in all cases, rendering vapour phase soldering a plausible alternative reflow method for soldering on flexible printed circuit boards

引用

页码：69 / 74

页数：6

共 50 条

[21] Analytical Solution of Heat Distribution Inside a Printed Circuit Board During Vapour Phase Soldering
Straubinger, Daniel
Bozsoki, Istvan
Illes, Balazs
Geczy, Attila
2019 42ND INTERNATIONAL SPRING SEMINAR ON ELECTRONICS TECHNOLOGY (ISSE), 2019,
[22] Reflow soldering of flexible printed circuit boards on sputtered iron-nickel coatings in the case of thermoprinting heads
Bugelreflowloeten von flexiblen Leiterplatten auf gesputterten Eisen-Nickel-Schichten am Beispiel von Thermodruckkoepfen
Elliger, W., 1600, (38):
[23] Electromagnetic interference from printed circuit boards connected by flexible printed circuit board
Ota, Masayuki
Sakusabe, Takashi
Takahashi, Takehiro
Schibuya, Noboru
2008 ASIA-PACIFIC SYMPOSIUM ON ELECTROMAGNETIC COMPATIBILITY AND 19TH INTERNATIONAL ZURICH SYMPOSIUM ON ELECTROMAGNETIC COMPATIBILITY, VOLS 1 AND 2, 2008, : 654 - +
[24] Robotic handling and assembly of flexible printed circuit boards
Massachusetts Inst of Technology, Cambridge, United States
Manuf Rev, 1 (6-21):
[25] A flexible method for applying adhesives to printed circuit boards
Lathrop, RR
ADHESIVES AGE, 1998, 41 (12): : 22 - +
[26] Selective soldering on printed circuit boards with endogenous induction heat at appropriate susceptors
Seehase D.
Kohlen C.
Neiser A.
Novikov A.
Nowottnick M.
Periodica polytechnica Electrical engineering and computer science, 2018, 62 (04): : 172 - 180
[27] Detection of soldering defects in Printed Circuit Boards with Hierarchical Marked Point Processes
Benedek, Csaba
PATTERN RECOGNITION LETTERS, 2011, 32 (13) : 1535 - 1543
[28] SDD-Net: Soldering defect detection network for printed circuit boards
Ling, Qin
Isa, Nor Ashidi Mat
Asaari, Mohd Shahrimie Mohd
NEUROCOMPUTING, 2024, 610
[29] Printed circuit boards for lead-free soldering: materials and failure mechanisms
Johander, Per
Tegehall, Per-Erik
Osman, Abelrahim Ahmed
Wetter, Goran
Andersson, Dag
CIRCUIT WORLD, 2007, 33 (02) : 10 - 16
[30] Effects of Temperature on the Wave Soldering of Printed Circuit Boards: CFD Modeling Approach
Aziz, M. S. Abdul
Abdullah, M. Z.
Khor, C. Y.
Ani, F. Che
Adam, N. H.
JOURNAL OF APPLIED FLUID MECHANICS, 2016, 9 (04) : 2053 - 2062

← 1 2 3 4 5 →