Optimization of the Injection Molding Process Parameters Based on Moldflow and Orthogonal Experiment

被引：3
|
作者：
Nie, Yong [1 ]
Zhang, Huimin [1 ]
Niu, Jiateng [1 ]
机构：
[1] Qingdao Univ Sci & Technol, Coll Electromech Engn, Shandong Prov Key Lab Polymer Mat Adv Mfg Technol, Qingdao 260061, Peoples R China
来源：
ADVANCED POLYMER PROCESSING III | 2013年 / 561卷
关键词：
Moldflow; orthogonal experiment; optimization; injection molding;
D O I：
10.4028/www.scientific.net/KEM.561.239
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
This article is using Moldflow analysis and orthogonal experimental method during the whole experiment. The injection molding process of motor cover is simulated under various technological conditions.After forming the maximum amount of warpage of plastic parts for evaluation.According to the range analysis of the comprehensive goal, the extent of the overall influence to the processing parameters, such as gate location, melt temperature, mold temperature and holding pressure is clarified.Through analyzing the diagrams of influential factors resulted from the simulation result,the optimized process parameter scheme is obtained and further verified by simulation.
引用
收藏
页码：239 / +
页数：2
相关论文
共 50 条
  • [41] Process parameters optimization in plastic injection molding using metamodel-based optimization: a comprehensive review
    Satoshi Kitayama
    The International Journal of Advanced Manufacturing Technology, 2022, 121 : 7117 - 7145
  • [42] The Parameters Optimization of Fusion Winglet Based on Orthogonal Experiment
    Luo, Yue
    Wang, Qi
    Du, Qi
    Ding, Hou-An
    INTERNATIONAL CONFERENCE ON CONTROL AND AUTOMATION (ICCA 2016), 2016, : 643 - 648
  • [43] Computer Simulation on Injection Molding Process of Automotive Engine Air intake Manifold Based on Moldflow
    Liu, Hanwu
    Zhang, Jiao
    Wang, Yang
    Liu, Junming
    PROCEEDINGS OF THE 2ND INTERNATIONAL CONFERENCE ON ELECTRONICS, NETWORK AND COMPUTER ENGINEERING (ICENCE 2016), 2016, 67 : 359 - 364
  • [44] Optimization of Injection Molding Parameters by Data Mining Method in PIM Process
    Wahi, Azizah
    Muhamad, Norhamidi
    Jamaludin, Khairur R.
    Rajabi, Javad
    Madraky, Abbas
    JURNAL TEKNOLOGI, 2012, 59
  • [45] Optimization of injection molding process parameters using sequential simplex algorithm
    Farshi, Behrooz
    Gheshmi, Siavash
    Miandoabchi, Elyar
    MATERIALS & DESIGN, 2011, 32 (01) : 414 - 423
  • [46] The study on the optimization of injection molding process parameters with gray relational analysis
    Fung, CP
    JOURNAL OF REINFORCED PLASTICS AND COMPOSITES, 2003, 22 (01) : 51 - 66
  • [47] Optimization of Microcellular Injection Molding Parameters
    Rizvi, S. J. A.
    Bhatnagar, N.
    INTERNATIONAL POLYMER PROCESSING, 2009, 24 (05) : 399 - 405
  • [48] Simulation-Based Optimization of Injection Molding Process Parameters for Minimizing Warpage by ANN and GA
    Nitnara, Chiwapon
    Tragangoon, Kumpon
    INTERNATIONAL JOURNAL OF TECHNOLOGY, 2023, 14 (02) : 422 - 433
  • [49] Experimental-Based Optimization of Injection Molding Process Parameters for Short Product Cycle Time
    Mukras, Saad M. S.
    ADVANCES IN POLYMER TECHNOLOGY, 2020, 2020 (2020)
  • [50] A Fuzzy Rule-based Network Model for Optimization of Process Parameters in Plastic Injection Molding
    Guo F.
    Wang R.
    Zhang Y.
    Zhou H.
    Li D.
    Jixie Gongcheng Xuebao/Journal of Mechanical Engineering, 2022, 58 (20): : 206 - 220
12345