Annealing behaviour of ultrafine-grained aluminium

被引：13

作者：

Sun, Pei-Ling ^{[1
]}

Zhao, Yonghao ^{[2
]}

Tseng, Tien-Yu ^{[3
]}

Su, Jiunn-Ren ^{[3
]}

Lavernia, Enrique J. ^{[4
]}

机构：

[1] Feng Chia Univ, Dept Mat Sci & Engn, Taichung 40724, Taiwan

[2] Nanjing Univ Sci & Technol, Sch Mat Sci & Engn, Nanostruct Mat Res Ctr, Nanjing 210094, Jiangsu, Peoples R China

[3] China Steel Corp, New Mat Res & Dev Dept, Kaohsiung 81233, Taiwan

[4] Univ Calif Davis, Dept Chem Engn & Mat Sci, Davis, CA 95616 USA

来源：

PHILOSOPHICAL MAGAZINE | 2014年 / 94卷 / 05期

基金：

中国国家自然科学基金;

关键词：

aluminium; hot and cold rolling; annealing; cooling rate; mechanical property; HIGH-TENSILE DUCTILITY; THERMAL-STABILITY; NANOCRYSTALLINE; STRENGTH; GROWTH; SIZE; MICROSTRUCTURE; STABILIZATION; SUBDIVISION; ALLOYS;

D O I：

10.1080/14786435.2013.856526

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Ultrafine-grained (UFG) aluminium, processed under fast cooling rate conditions (12Ks(-1)) following hot rolling (water quenched) exhibits enhanced thermal stability due to an increase in concentration of solid solution atoms, relative to the furnace cooled material. The influence of fraction recrystallized on yield stress and uniform elongation is reported to exhibit a slight deviation from the linear behaviour that is anticipated on the basis of the rule-of-mixtures. This result was rationalized on the basis of differences in the spatial distributions of the UFG and coarse grains and/or dislocation recovery mechanisms.

引用

页码：476 / 491

页数：16

共 50 条

[31] Improvement of formability of ultrafine-grained materials by post-SPD annealing
Saray, O.
Purcek, G.
Karaman, I.
Maier, H. J.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2014, 619 : 119 - 128
[32] Inhomogeneous softening during annealing of ultrafine-grained silver processed by HPT
Hegedus, Zoltan
Gubicza, Jeno
Szommer, Peter
Chinh, Nguyen Q.
Huang, Yi
Langdon, Terence G.
JOURNAL OF MATERIALS SCIENCE, 2013, 48 (21) : 7384 - 7391
[33] ANNEALING-INDUCED GRAIN ROTATION IN ULTRAFINE-GRAINED ALUMINUM ALLOY
Danilenko, V. N.
Bachurin, D., V
Nazarov, A. A.
REVIEWS ON ADVANCED MATERIALS SCIENCE, 2018, 55 (1-2) : 69 - 77
[34] Recrystallization and grain growth due to annealing of an ultrafine-grained Al alloy
Loucif, Aicha
Figueiredo, Roberto B.
Baudin, Thierry
Brisset, Francois
Langdon, Terence G.
RECRYSTALLIZATION AND GRAIN GROWTH V, 2013, 753 : 303 - +
[35] Monitoring of Self-Annealing in Ultrafine-Grained Silver Using Nanoindentation
Gubicza, Jeno
Chinh, Nguyen Q.
Langdon, Terence G.
NANOSCIENCE AND NANOTECHNOLOGY LETTERS, 2010, 2 (04) : 294 - 297
[36] Inhomogeneous softening during annealing of ultrafine-grained silver processed by HPT
Zoltán Hegedűs
Jenő Gubicza
Péter Szommer
Nguyen Q. Chinh
Yi Huang
Terence G. Langdon
Journal of Materials Science, 2013, 48 : 7384 - 7391
[37] High Strain Behaviour of Ultrafine-grained Aluminium Alloys Processed Through the Severe Plastic Deformation Techniques: A Review
Hembram, Marshal
Singh, Pallavi
Kumar, Nikhil
METALLOGRAPHY MICROSTRUCTURE AND ANALYSIS, 2022, 11 (05) : 684 - 703
[38] Ultrafine-Grained Steel Produced by Warm Rolling and Annealing of Lath Martensite
Zhao, Xin
Yang, Xiaoling
NANOMATERIALS BY SEVERE PLASTIC DEFORMATION: NANOSPD5, PTS 1 AND 2, 2011, 667-669 : 863 - +
[39] Understanding material behaviour of ultrafine-grained aluminium nano-composite sheets with emphasis on stretch and bending deformation
Deb, S.
Panigrahi, S. K.
Weiss, M.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2021, 293
[40] Effect of annealing treatment on the microstructure and mechanical properties of ultrafine-grained aluminum
Zhao, F. X.
Xu, X. C.
Liu, H. Q.
Wang, Y. L.
MATERIALS & DESIGN, 2014, 53 : 262 - 268

← 1 2 3 4 5 →