Simulation Research of the Influence of Compression Ratio on the Performance of an Aircraft Piston Diesel Engine

被引:2
|
作者
Grabowski, Lukasz [1 ]
Karpinski, Pawel [1 ]
Magryta, Pawel [1 ]
机构
[1] Lublin Univ Technol, Fac Mech Engn, Dept Thermodynam Fluid Mech & Aviat Prop Syst, Ul Nadbystrzycka 36, PL-20618 Lublin, Poland
关键词
aircraft; compression ratio; diesel engine; opposed-piston; two-stroke; COMBUSTION; EMISSIONS; OPTIMIZATION; IMPINGEMENT; PRESSURE; MODEL;
D O I
10.12913/22998624/122195
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
In recent years, the opposed-piston engines have become increasingly popular in the automotive and aerospace industries. Therefore, it is necessary to conduct the research on this type of drive. The paper presents the simulation research of a two-stroke opposed-piston diesel engine designed for propulsion of light aircrafts. The influence of the change of the compression ratio on the selected engine performance was investigated (indicated mean effective pressure, peak firing temperature and pressure, specific fuel consumption, power consumed by the compressor). The AVL BOOST software was used to perform the simulation tests. A zero-dimensional engine model equipped with a mechanical compressor was developed. On the basis of the created model, a series of calculations was performed for the assumed values of the compression ratio for four engine operating points: take-off power, maximum continuous power and cruising power at two different altitudes. The obtained results were subjected to a comparative analysis and the most important conclusions connected with the influence of the change in the compression ratio on the achieved performance were presented.
引用
收藏
页码:175 / 181
页数:7
相关论文
共 50 条
  • [41] CFD Analysis of Charge Exchange in an Aircraft Opposed-Piston Diesel Engine
    Czyz, Zbigniew
    Siadkowska, Ksenia
    Sochaczewski, Rafal
    III INTERNATIONAL CONFERENCE OF COMPUTATIONAL METHODS IN ENGINEERING SCIENCE (CMES 18), 2019, 252
  • [42] Performance Comparison of Microalgae Biodiesel Blends with Petro–Diesel on Variable Compression Ratio Engine
    Soni A.K.
    Kumar S.
    Pandey M.
    Journal of The Institution of Engineers (India): Series E, 2022, 103 (1) : 53 - 63
  • [43] Improving the performance of a diesel engine by changing injectors characteristics after reduction on the compression ratio
    Chamehsara, Saeed
    Karami, Mohammadreza
    JOURNAL OF MECHANICAL ENGINEERING AND SCIENCES, 2021, 15 (02) : 8153 - 8168
  • [44] Performance characteristics of a supercharged variable compression ratio diesel engine fueled by biodiesel blends
    El-Adawy, Mohammed
    El-Kasaby, M.
    Eldrainy, Yehia A.
    ALEXANDRIA ENGINEERING JOURNAL, 2018, 57 (04) : 3473 - 3482
  • [45] Influence of injection timing and compression ratio on performance, emission and combustion characteristics of Annona methyl ester operated diesel engine
    Ramalingam, Senthil
    Rajendran, Silambarasan
    Nattan, Ravichandiran
    ALEXANDRIA ENGINEERING JOURNAL, 2015, 54 (03) : 295 - 302
  • [46] Research on simulation of friction heat in piston engine
    Department of scientific Research, Bengbu Tanke Institute, Bengbu 233050, China
    不详
    Neiranji Gongcheng, 2006, 4 (47-50):
  • [47] Influence of compression ratio on combustion and performance characteristics of direct injection compression ignition engine
    Hariram, V.
    Shangar, R. Vagesh
    ALEXANDRIA ENGINEERING JOURNAL, 2015, 54 (04) : 807 - 814
  • [48] AIRCRAFT ENGINE PERFORMANCE AUGMENTED BY WET COMPRESSION
    Gkoutzamanis, Vasilis G.
    Psaropoulos, Michalis K.
    Kalfas, Anestis I.
    PROCEEDINGS OF ASME TURBO EXPO 2023: TURBOMACHINERY TECHNICAL CONFERENCE AND EXPOSITION, GT2023, VOL 1, 2023,
  • [49] OPTIMIZATION OF COMPRESSION RATIO OF JATROPHA OIL BLEND WITH DIESEL FUELLED ON VARIABLE COMPRESSION RATIO ENGINE
    De, Biswajit
    Panua, Rajsekhar
    FRONTIERS IN HEAT AND MASS TRANSFER, 2014, 5
  • [50] The Performance Simulation and Optimization Research on Intake Port of Locomotive Diesel Engine
    Cui Hongjiang
    Li Minghai
    Guan Ying
    MANUFACTURING SCIENCE AND MATERIALS ENGINEERING, PTS 1 AND 2, 2012, 443-444 : 1007 - 1013