A Comparative Investigation of Drilling and Milling Micro Holes Using Micro-EDM

被引：0
|
作者：
Li, Yiquan [1 ]
Hou, Wanwu [1 ]
Xu, Jinkai [1 ]
Yu, Huadong [1 ]
机构：
[1] Changchun Univ Sci & Technol, Coll Mech & Elect Engn, Changchun, Jilin Province, Peoples R China
来源：
2016 6TH IEEE INTERNATIONAL CONFERENCE ON MANIPULATION, MANUFACTURING AND MEASUREMENT ON THE NANOSCALE (IEEE 3M-NANO) | 2016年
关键词：
micro-EDM; drilling; milling; depth to diameter ratio; rotate speed; DEEP HOLE;
D O I：
暂无
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
Micro Electrical Discharge Machining (micro-EDM), is one of the most important technologies for the machining of difficult-to-cut materials, and it can be considered as one of the most promising manufacturing process for fabricating micro holes. Micro-EDM is suitable for machining micro holes, while it is still hard to machining holes with high depth. The study will make a research on drilling and milling holes using micro-EDM, the milling process shows better performance especially for the holes with high depth to diameter ratio; while drilling process could gain higher processing speed and better geometrical properties of the micro-holes.
引用
收藏
页码：212 / 216
页数：5
相关论文
共 50 条
  • [31] Optimization of micro-EDM drilling of inconel 718 superalloy
    Mustafa Ay
    Ulaş Çaydaş
    Ahmet Hasçalık
    [J]. The International Journal of Advanced Manufacturing Technology, 2013, 66 : 1015 - 1023
  • [32] Optimization of micro-EDM drilling of inconel 718 superalloy
    Department of Manufacturing, Technical Education Faculty, University of Firat, 23119 Elazig, Turkey
    [J]. Çaydaş, U. (ucaydas@firat.edu.tr), 1600, Springer London (66): : 5 - 8
  • [33] A model to predict manufacturing cost for micro-EDM drilling
    D'Urso, G.
    Quarto, M.
    Ravasio, C.
    [J]. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2017, 91 (5-8): : 2843 - 2853
  • [34] Process performance of micro-EDM drilling of stainless steel
    G. D’Urso
    G. Maccarini
    C. Ravasio
    [J]. The International Journal of Advanced Manufacturing Technology, 2014, 72 : 1287 - 1298
  • [35] Micro-EDM milling of electrically nonconducting zirconia ceramics
    Schubert, A.
    Zeidler, H.
    Hahn, M.
    Hackert-Oschaetzchen, M.
    Schneider, J.
    [J]. PROCEEDINGS OF THE SEVENTEENTH CIRP CONFERENCE ON ELECTRO PHYSICAL AND CHEMICAL MACHINING (ISEM), 2013, 6 : 297 - 302
  • [36] Performance analysis of powder-assisted micro-drilling operation using micro-EDM
    Yadav, Sharad
    Sisodia, Naman
    Agarwal, Deepak
    Singh, Rabesh Kumar
    Sharma, Anuj Kumar
    [J]. PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART C-JOURNAL OF MECHANICAL ENGINEERING SCIENCE, 2024, 238 (15) : 7627 - 7639
  • [37] Optimization of micro-EDM drilling of inconel 718 superalloy
    Ay, Mustafa
    Caydas, Ulas
    Hascalik, Ahmet
    [J]. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2013, 66 (5-8): : 1015 - 1023
  • [38] Process performance of micro-EDM drilling of stainless steel
    D'Urso, G.
    Maccarini, G.
    Ravasio, C.
    [J]. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2014, 72 (9-12): : 1287 - 1298
  • [39] A model to predict manufacturing cost for micro-EDM drilling
    G. D’Urso
    M. Quarto
    C. Ravasio
    [J]. The International Journal of Advanced Manufacturing Technology, 2017, 91 : 2843 - 2853
  • [40] Workpiece and electrode influence on micro-EDM drilling performance
    D'Urso, G.
    Merla, C.
    [J]. PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY, 2014, 38 (04): : 903 - 914
12345