INFLUENCE OF THERMOMECHANICAL PROCESSING ON THE COLD DEFORMABILITY OF LOW-CARBON STEEL

被引：0

作者：

Barucija, Besim ^{[1
]}

Oruc, Mirsada ^{[1
]}

Beganovic, Omer ^{[1
]}

Rimac, Milenko ^{[1
]}

Muhamedagic, Sulejman ^{[2
]}

机构：

[1] Univ Zenica, Inst Met Kemal Kapetanovic Zenica, Zenica, Bosnia & Herceg

[2] Univ Zenica, Fac Met & Mat, Zenica, Bosnia & Herceg

来源：

MATERIALI IN TEHNOLOGIJE | 2013年 / 47卷 / 05期

关键词：

low-carbon steel; deformation testing; compression; visual control;

D O I：

暂无

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

The group of steels intended for the production of bolts and nuts from the production programme of the Zenica Steel Plant, Zenica, nowadays called Arcelor Mittal Zenica, includes, among others, the steel C8C according to EN 10263-2. In this paper, the results of testing the above-mentioned steel, with the nitrogen content of more than 0.007 %, manufactured within a specifically defined technological programme, are presented. The testing of the rolled bars with a diameter of 12 mm is focused, among the mechanical and metallographic tests, especially on the technological compression test in the cold state that is normally performed as an additional control test in the production. The cold compression of the test samples has been performed in four degrees of deformation and at two different speeds of compressing tools. We determined the dependence of the resistance to deformation of the material on the degree and speed of deformation. The surface inspection of the tested samples was performed with visual control with the aim to determine deformability of the bars produced in this way.

引用

页码：665 / 668

页数：4

共 50 条

[11] Effect of Controlled Thermomechanical Processing Routes on the Structural and Textural States of Low-Carbon Low-Alloy Steel
Lobanov, M. L.
Platov, S. I.
Zorina, M. A.
Urtsev, N. V.
Maslennikov, K. B.
METAL SCIENCE AND HEAT TREATMENT, 2023, 65 (7-8) : 494 - 500
[12] Effect of Cooling Rate on the Structure of Low-Carbon Low-Alloy Steel After Thermomechanical Controlled Processing
Lobanov, M. L.
Krasnov, M. L.
Urtsev, V. N.
Danilov, S., V
Pastukhov, V., I
METAL SCIENCE AND HEAT TREATMENT, 2019, 61 (1-2) : 32 - 38
[13] INFLUENCE OF AMOUNT OF REDUCTION ON PROPERTIES OF COLD-ROLLED LOW-CARBON STEEL
YUDOVICH, SZ
BELCHENK.GI
SHULIKA, NA
BELYY, ET
RUSSIAN METALLURGY, 1973, (02): : 98 - 103
[14] Effect of Controlled Thermomechanical Processing Routes on the Structural and Textural States of Low-Carbon Low-Alloy Steel
M. L. Lobanov
S. I. Platov
M. A. Zorina
N. V. Urtsev
K. B. Maslennikov
Metal Science and Heat Treatment, 2023, 65 : 485 - 493
[15] INFLUENCE OF STARTING STRUCTURE ON RECRYSTALLIZATION OF COLD-ROLLED LOW-CARBON STEEL
GRABOVSK.VY
SHTEKHNO, ON
NATAPOV, BS
OLSHANET.VE
STEEL IN THE USSR, 1971, 1 (12): : 981 - &
[16] THE INFLUENCE OF NON-METALLIC INCLUSIONS ON COLD UPSETABILITY OF LOW-CARBON STEEL
LAHTI, I
SULONEN, M
SCANDINAVIAN JOURNAL OF METALLURGY, 1982, 11 (01) : 9 - 16
[17] Effect of Cooling Rate on the Structure of Low-Carbon Low-Alloy Steel After Thermomechanical Controlled Processing
M. L. Lobanov
M. L. Krasnov
V. N. Urtsev
S. V. Danilov
V. I. Pastukhov
Metal Science and Heat Treatment, 2019, 61 : 32 - 38
[18] On the use of thermomechanical processing to enhance the strength-ductility-toughness balance of plain low-carbon steel
Khorasani, Fatemeh
Jamaati, Roohollah
Aval, Hamed Jamshidi
HELIYON, 2024, 10 (17)
[19] AUSTENITE GRAIN-REFINEMENT OF LOW-CARBON STEEL BY THERMOMECHANICAL PROCESSING AND THE EFFECTS OF MINOR ADDITION OF NIOBIUM
TOKIZANE, M
MATSUMURA, N
TRANSACTIONS OF THE IRON AND STEEL INSTITUTE OF JAPAN, 1982, 22 (02) : B27 - B27
[20] Effect of Composition and Thermomechanical Processing on Structure and Properties of Low-Carbon Sheet Steel for Forming Applications.
Rajkovic, V.
1600, (25):

← 1 2 3 4 5 →