Nanostructured martensite-austenite dual phase steels

被引：3

作者：

Hu, F. ^{[1
]}

Wu, K. M. ^{[1
]}

Misra, R. D. K. ^{[2
]}

机构：

[1] Wuhan Univ Sci & Technol, Int Res Inst Steel Technol, Wuhan 430081, Peoples R China

[2] Univ Louisiana Lafayette, Ctr Struct & Funct Mat, Lafayette, LA 70504 USA

来源：

MATERIALS SCIENCE AND TECHNOLOGY | 2012年 / 28卷 / 11期

关键词：

Microstructure; Hardness; Martensite; Bainite; Dual phase steels; PARTITIONING-TEMPERING PROCESS; LOW-TEMPERATURE BAINITE; HIGH-STRENGTH STEEL; MECHANICAL-PROPERTIES; HEAT-TREATMENT; CARBON; TRANSFORMATION; FERRITE;

D O I：

10.1179/1743284712Y.0000000068

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Nanostructured martensite-austenite microstructure was achieved by a quenching-partitioning-tempering (Q-P-T) treatment of high carbon low temperature bainitic steel. Microstructure observations showed that the nanostructured steel consisted of fine martensite (about 25 nm in thickness), retained austenite and carbides. X-ray diffraction analysis indicated that carbon was partitioned into austenite after martensite transformation. High hardness (about 655 HV1) and relatively high retained austenite fraction (0.36-0.41) was attained. The heat treatment times were greatly reduced, nearly equal or higher hardness and retained austensite fraction were achieved by Q-P-T treatment, compared with low temperature super bainite process.

引用

下载

页码：1314 / 1319

页数：6

共 50 条

[21] A thermomagnetic study of the martensite-austenite phase transition in the maraging 350 steel
Tavares, SSM
Abreu, HFG
Neto, JM
da Silva, MR
Popa, I
JOURNAL OF ALLOYS AND COMPOUNDS, 2003, 358 (1-2) : 152 - 156
[22] Toughening mechanisms of low transformation temperature deposited metals with martensite-austenite dual phases
Wu, Shipin
Wang, Dongpo
Di, Xinjie
Zhang, Zhi
Feng, Zhongyuan
Liu, Xiaoqian
Li, Yezheng
Meng, Xianqun
JOURNAL OF MATERIALS SCIENCE, 2018, 53 (05) : 3720 - 3734
[23] Additive manufacturing of novel heterostructured martensite-austenite dual-phase steel through in-situ alloying
Su, Jinlong
Tan, Chaolin
Ng, Fern Lan
Weng, Fei
Chen, Lequn
Jiang, Fulin
Teng, Jie
Chew, Youxiang
MATERIALS TODAY COMMUNICATIONS, 2022, 33
[24] Strength-toughness improvement of martensite-austenite dual phase deposited metals after austenite reversed treatment with short holding time
Wu, Shipin
Wang, Dongpo
Di, Xinjie
Li, Chengning
Zhang, Zhi
Zhou, Zhijin
Liu, Xiuguo
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2019, 755 : 57 - 65
[25] LATTICE IMAGING STUDY OF A MARTENSITE-AUSTENITE INTERFACE
SINCLAIR, R
MOHAMED, HA
ACTA METALLURGICA, 1978, 26 (04): : 623 - 628
[26] Influence of martensite-austenite (MA) on impact toughness of X80 line pipe steels
Huda, Nazmul
Midawi, Abdelbaset R. H.
Gianetto, James
Lazor, Robert
Gerlich, Adrian P.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2016, 662 : 481 - 491
[27] Experimental-numerical study on strain and stress partitioning in bainitic steels with martensite-austenite constituents
Fujita, Noriki
Ishikawa, Nobuyuki
Roters, Franz
Tasan, Cemal Cem
Raabe, Dierk
INTERNATIONAL JOURNAL OF PLASTICITY, 2018, 104 : 39 - 53
[28] Towards engineering of mechanical properties through stabilization of austenite in ultrafine grained martensite-austenite dual phase steel processed by accumulative roll bonding
Tirekar, S.
Jafarian, H. R.
Eivani, A. R.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2017, 684 : 120 - 126
[29] Automated segmentation of martensite-austenite islands in bainitic steel
Ackermann, Marc
Iren, Deniz
Wesselmecking, Sebastian
Shetty, Deekshith
Krupp, Ulrich
Materials Characterization, 2022, 191
[30] STRUCTURE OF MARTENSITE-AUSTENITE ISLANDS IN GRANULAR BAINITE.
Bold, Tadeusz
Garbarz, Bogdan
Praktische Metallographie/Practical Metallography, 1980, 17 (07): : 338 - 343

← 1 2 3 4 5 →