Optimization of a scroll compressor for liquid flooding

被引：19

作者：

Bell, Ian H. ^{[1
]}

Groll, Eckhard A. ^{[1
]}

Braun, James E. ^{[1
]}

King, Galen B. ^{[1
]}

Horton, W. Travis ^{[1
]}

机构：

[1] Purdue Univ, Dept Mech Engn, W Lafayette, IN 47906 USA

来源：

INTERNATIONAL JOURNAL OF REFRIGERATION-REVUE INTERNATIONALE DU FROID | 2012年 / 35卷 / 07期

关键词：

Scroll compressors; Liquid flooding; Isothermal compression; High efficiency;

D O I：

10.1016/j.ijrefrig.2012.07.011

中图分类号：

O414.1 [热力学];

学科分类号：

摘要：

In two companion papers, simulation models for the working processes of liquid-flooded scroll compressors and expanders have been developed and validated against experimental data. In this study, analytic models are presented for the modes of irreversibility generation in the liquid-flooded scroll compressor including built-in volume ratio maladjustment, pressure drop and leakage. A thermodynamic model is used to derive the ideal volume ratio for a liquid-flooded compressor, which is higher than that of dry compression. An optimum set of built-in volume ratio and scroll base circle radius is found which maximizes the overall isentropic efficiency by minimizing the leakage and pressure drop irreversibilities. The irreversibility generation models are used to optimize a scroll compressor for the Liquid-Flooded Ericsson cycle application. The model predicts scroll compressor overall isentropic efficiency of over 80% (based on the shaft power) at an oil mass fraction of 88%. (C) 2012 Elsevier Ltd and IIR. All rights reserved.

引用

页码：1901 / 1913

页数：13

共 50 条

[41] Numerical modelling of temperature distribution for orbiting scroll wrap in an air scroll compressor
Qiang Jianguo
Tao Wen
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER, 2013, 67 : 678 - 689
[42] Exergetic optimization of a key design parameter in heat pump systems with economizer coupled with scroll compressor
Ma, Guoyuan
Li, Xianguo
ENERGY CONVERSION AND MANAGEMENT, 2007, 48 (04) : 1150 - 1159
[43] SOME DESIGN PROBLEMS OF SCROLL COMPRESSOR.
Morishita, Etsuo
Sugihara, Masahiro
Nippon Kikai Gakkai Ronbunshu, B Hen/Transactions of the Japan Society of Mechanical Engineers, Part B, 1986, 52 (477): : 2121 - 2130
[44] Analysis of Loads at Crankshaft Bearing for Scroll Compressor
Li Chao
Yu Yang
Zhao Man
ADVANCES IN INTELLIGENT STRUCTURE AND VIBRATION CONTROL, 2012, 160 : 42 - 46
[45] R-290 SCROLL COMPRESSOR TECHNOLOGY
Zhang, Leping
Ginies, Pierre
Dewitte, Philippe
11TH IIR GUSTAV LORENTZEN CONFERENCE ON NATURAL REFRIGERANTS (2014): NATURAL REFRIGERANTS AND ENVIRONMENTAL PROTECTION, 2014, : 186 - 192
[46] Ball behavior of ball coupling for scroll compressor
Hirano, Takashia
Kawarita, Kazuaki
Hagimoto, Klyoshi
Maruiwa, Yasuharu
Journal of Japanese Society of Tribologists, 1994, (02)
[47] Development advantage and key techniques for scroll compressor
Feng, Jianmei
Qu, Zongchang
Zhongguo Jixie Gongcheng/China Mechanical Engineering, 2002, 13 (19):
[48] Scroll compressor flow modelling - a computational investigation
Karagiorgis, G
Stosic, N
Smith, IK
INTERNATIONAL CONFERENCE ON COMPRESSORS AND THEIR SYSTEMS, 1999, 1999 (06): : 289 - 300
[49] Optimization of an oil charge amount on electric driven scroll compressor for eco-friendly vehicle
Nam, Donglim
Lee, Poyoung
Lee, Geonho
Kwon, Yunki
Lee, Jinho
INTERNATIONAL JOURNAL OF REFRIGERATION-REVUE INTERNATIONALE DU FROID, 2015, 57 : 54 - 61
[50] Oil flow at discharge valve in a scroll compressor
Zimmermann, A. J. P.
Hrnjak, P. S.
8TH INTERNATIONAL CONFERENCE ON COMPRESSORS AND THEIR SYSTEMS, 2013, : 311 - 320

← 1 2 3 4 5 →