An Investigation into Mechanical Properties of Ductile Cast Iron with Different Heat Treatment Processes

被引：2

作者：

Moussa, Romany R. ^{[1
,2
]}

Ali, Amer E. ^{[3
]}

Abdel-Magied, Ragab K. ^{[3
]}

Elshiekh, Mohamed N. ^{[1
]}

机构：

[1] Beni Suef Univ, Fac Ind Educ, Dept Prod Technol, Salah Salem St, Bani Suwayf 62511, Egypt

[2] Budapest Univ Technol & Econ, Fac Mech Engn, Dept Mat Sci & Engn, POB 91, H-1521 Budapest, Hungary

[3] Beni Suef Univ, Fac Engn, Dept Mech Engn, Salah Salem St, Bani Suwayf 62511, Egypt

来源：

PERIODICA POLYTECHNICA-MECHANICAL ENGINEERING | 2019年 / 63卷 / 03期

关键词：

heat treatment; DCI (Ductile Cast Iron); quenching; tempering; austempering;

D O I：

10.3311/PPme.13672

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

The mechanical properties as well as microstructure of the ductile cast iron (DCI) are most likely affected by heat treatments. In this work, the mechanical properties of different heat treated of DCI alloy were investigated. Two heat treatment (HT) processes were conducted for DCI; austempering and quenching followed by lower tempering. The melted alloy of DCI was poured in Y-block, from which the specimens of the mechanical tests were prepared. Experimental tests were carried out to investigate the effect of these HT processes on the mechanical properties. A comparison between mechanical properties due to HT and as cast DCI are presented and discussed. The results showed that there is a difference in microstructure, homogeneity, wear rate and compression of DCI based on the conducted heat treatment.

引用

页码：183 / 187

页数：5

共 50 条

[21] Microstructures and mechanical properties of troostite nodular cast iron by heat treatment
Liu, Kegao
Xu, Aimin
MATERIALS ENGINEERING FOR ADVANCED TECHNOLOGIES, PTS 1 AND 2, 2011, 480-481 : 207 - 210
[22] Influence of Heat Treatment on Microstructural and Mechanical Properties of Nodular Cast Iron
Kruthiventi S.
Basavakumar K.G.
Nambala S.
Subramanyacharyulu G.
Kruthiventi, S. (satyasai222@gmail.com), 1600, Springer (95): : 75 - 79
[23] AUSTEMPERING HEAT TREATMENT STUDY OF CAST DUCTILE IRON: ANALYSIS OF MECHANICAL AND MICROSTRUCTURAL PROPERTIES, ACCORDING TO THE A897M STANDARD SPECIFICATIONS FOR AUSTEMPERED DUCTILE IRON CASTINGS
Schifino, Alessandra Regina Machado
Sant'anna, Felipe Riegel
Trindade, Alexandre Pinto
PERIODICO TCHE QUIMICA, 2018, 15 (29): : 64 - 74
[24] Factors influencing microstructure and mechanical properties of as cast and heat treated 400-18 grade ductile cast iron
Riposan, I.
Chisamera, M.
Stan, S.
INTERNATIONAL JOURNAL OF CAST METALS RESEARCH, 2007, 20 (02) : 64 - 67
[25] INFLUENCE OF AUSTEMPERING HEAT TREATMENT ON MECHANICAL AND CORROSION PROPERTIES OF DUCTILE IRON SAMPLES
Janjic, M.
Avdusinovic, H.
Jurkovic, Z.
Bikic, F.
Savicevic, S.
METALURGIJA, 2016, 55 (03): : 325 - 328
[26] Dual matrix structure (DMS) ductile cast iron: The effect of heat treating variables on the mechanical properties
Rashidi, AM
Moshrefi-Torbati, M
INTERNATIONAL JOURNAL OF CAST METALS RESEARCH, 2001, 13 (05) : 293 - 297
[27] Comparison of Mechanical Properties of Ductile Cast Iron and Magnesium-Treated Malleable Cast Iron.
Lepand, H.
Komp, U.
Jahnkow, H.
1978, (05): : 51 - 64
[28] Effect of Different Heat Treatment Processes on Microstructures and Mechanical Properties of DP SteelsEffect of Different Heat Treatment Processes on Microstructures and Mechanical Properties of DP SteelsJiang
Yinghua Jiang
JOM, 2025, 77 (1) : 186 - 192
[29] Investigation of microstructural and mechanical properties of austempered steel bar-reinforced ductile cast iron composite
Kazemi, M.
Kiani-Rashid, A. R.
Nourian, A.
Babakhani, A.
MATERIALS & DESIGN, 2014, 53 : 1047 - 1051
[30] MECHANICAL-PROPERTIES OF DUCTILE CAST-IRON WITH DUPLEX MATRIX
WADE, N
UEDA, Y
TRANSACTIONS OF THE IRON AND STEEL INSTITUTE OF JAPAN, 1981, 21 (02) : 117 - 126

← 1 2 3 4 5 →