Theoretical investigation on heat-electricity decoupling technology of low-pressure steam turbine renovation for CHPs

被引：5

作者：

Hu, Qingbo ^{[1
]}

Wang, Kun ^{[1
]}

Zhang, Li ^{[1
]}

Zhou, Liansheng ^{[1
]}

Chen, Rong ^{[1
]}

Wang, Shan ^{[2
]}

Zhang, Yu ^{[1
]}

Li, Guohao ^{[1
]}

机构：

[1] Tianjin Elect Power Sci & Res Inst, Tianjin 300384, Peoples R China

[2] Xi An Jiao Tong Univ, State Key Lab Multiphase Flow Power Engn, Xian 710049, Shaanxi, Peoples R China

来源：

THIRD INTERNATIONAL CONFERENCE ON ENERGY ENGINEERING AND ENVIRONMENTAL PROTECTION | 2019年 / 227卷

关键词：

D O I：

10.1088/1755-1315/227/4/042043

中图分类号：

TE [石油、天然气工业]; TK [能源与动力工程];

学科分类号：

0807 ; 0820 ;

摘要：

The power grid peaking capacity is insufficient due to the increasing installed capacity of renewable power. Moreover, it is also restricted by the operation mode of combined heat and power units (CHPs), the minimum electricity loads of which are determined by the heat load. It is significant to study the heat-electricity decoupling technologies for CHPs. Therefore, the low-pressure steam turbine renovation technology is studied in this paper with a 300MW unit as reference case. Results show that the minimum electric load rate and the coal consumption are decreased, and the heat-electricity ratio is increased significantly for CHP with low-pressure steam turbine renovation. When the heat load is 1200 GJ/h, the minimum electric load rate and coal consumption with low-pressure steam turbine renovation can be reduced by 32.4 and 30.9 % respectively. The heat-electricity ratio can be increased by 68.8 % after renovation of low-pressure steam turbine.

引用

页数：7

共 50 条

[31] Investigation on Low-Pressure Steam Turbine Exhaust Hood Modelling through Computational Fluid Dynamic Simulations
Fondelli, Tommaso
Diurno, Tommaso
Palanti, Lorenzo
Andreini, Antonio
Facchini, Bruno
Nettis, Leonardo
Arcangeli, Lorenzo
Maceli, Nicola
74TH ATI NATIONAL CONGRESS: ENERGY CONVERSION: RESEARCH, INNOVATION AND DEVELOPMENT FOR INDUSTRY AND TERRITORIES, 2019, 2191
[32] NUMERICAL INVESTIGATION ON THE AERODYNAMIC PERFORMANCE OF A LOW-PRESSURE STEAM TURBINE EXHAUST HOOD USING DOE ANALYSIS
Diurno, Tommaso
Fondelli, Tommaso
Nettis, Leonardo
Maceli, Nicola
Arcangeli, Lorenzo
Andreini, Antonio
Facchini, Bruno
PROCEEDINGS OF THE ASME TURBO EXPO: TURBOMACHINERY TECHNICAL CONFERENCE AND EXPOSITION, VOL 9, 2020,
[33] A generic low-pressure steam turbine test case for aeromechanics and condensation
Fuhrer, Christopher
Gruebel, Marius
Vogt, Damian M.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART A-JOURNAL OF POWER AND ENERGY, 2019, 233 (07) : 953 - 958
[34] The Effect of Rotor Casing on Low-Pressure Steam Turbine and Diffuser Interactions
Singh, Gursharanjit
Wheeler, Andrew P. S.
Singh, Gurnam
JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME, 2017, 139 (02):
[35] Experience With Weld Repair of Low-Pressure Steam Turbine Rotors.
Amos, D.R.
Clark, R.E.
Kramer, L.D.
Schmerling, J.M.
Der Maschinenschaden Berlin, 1986, 59 (05): : 202 - 207
[36] Some aspects of cfd modeling in the analysis of a low-pressure steam turbine
Rubechini, Filippo
Marconcini, Michele
Arnone, Andrea
Cecchi, Stefano
Dacca, Federico
Proceedings of the ASME Turbo Expo 2007, Vol 6, Pts A and B, 2007, : 519 - 526
[37] Failure investigations of last stage low-pressure steam turbine blade
Sehra, Nitin
Rani, Sushila
JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY, 2023, 37 (08) : 4017 - 4023
[38] INVESTIGATING THE EXHAUST HOOD OF A STEAM-TURBINE LOW-PRESSURE CYLINDER
KASILOV, VF
GALATSAN, VN
KONEV, VA
DENISOV, VN
THERMAL ENGINEERING, 1990, 37 (05) : 241 - 244
[39] Crack evaluation of the fourth stage blade in a low-pressure steam turbine
Kim, Hyojin
ENGINEERING FAILURE ANALYSIS, 2011, 18 (03) : 907 - 913
[40] Moving Blade Failure in the Low-Pressure Turbine of a Steam Turbo Set
Mundt, G.
Neidel, A.
Matijasevic-Lux, B.
PRAKTISCHE METALLOGRAPHIE-PRACTICAL METALLOGRAPHY, 2012, 49 (12): : 782 - 791

← 1 2 3 4 5 →