Effect of Modifiers on Injection Molding of Waste Polyethylene Drip Tape

被引：0
|
作者：
Guo, Bin [1 ]
Wu, Shou-Jun [1 ]
Zhu, De-Lan [1 ]
机构：
[1] Northwest A&F Univ, Coll Water Resources & Architectural Engn, Yangling 712100, Shaanxi, Peoples R China
来源：
PROCEEDINGS OF THE 2015 INTERNATIONAL CONFERENCE ON MATERIAL SCIENCE AND APPLICATIONS (ICMSA 2015) | 2015年 / 3卷
关键词：
Polyethylene; Injection Molding; Ethylene-vinyl Acetate Copolymer; Dicumyl Peroxide; MECHANICAL-PROPERTIES; CROSS-LINKING; BLENDS;
D O I：
暂无
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
In this work, effects of Ethylene-vinyl acetate copolymer (EVA) and Dicumyl peroxide (DCP) on injection molding of recycled polyethylene (PE) materials obtained from a waste disposable drip tape are studied. Under injected at 175-230 degrees C and 35-40 MPa, the recycled PE materials with EVA showed good injection moldability, while those with DCP showed poor injection moldability with DCP introduction increasing. Under injected at 135-145 degrees C and 50-60 MPa, the recycled PE materials with DCP can be well injection molded.
引用
收藏
页码：948 / 951
页数：4
相关论文
共 50 条
  • [41] EFFECT OF PROCESSING FACTORS (INJECTION-MOLDING) ON STRENGTH PROPERTIES OF HIGH-DENSITY POLYETHYLENE AND REVEALMENT OF AN OPTIMUM
    ALIGULIEV, RM
    ALIYEV, GM
    ZELENEV, YV
    KERIMOV, DA
    RAGIMOVA, DK
    IZVESTIYA AKADEMII NAUK AZERBAIDZHANSKOI SSR SERIYA FIZIKO-TEKHNICHESKIKH I MATEMATICHESKIKH NAUK, 1978, (03): : 100 - 105
  • [42] The effect of limescale on heat transfer in injection molding
    Zink, Bela
    Kovacs, Jozsef Gabor
    INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER, 2017, 86 : 101 - 107
  • [43] Effect of microstructures on the shrinkage of injection molding product
    Yue Wu
    Yao Gong
    Kyoung Je Cha
    Jang Min Park
    Journal of Mechanical Science and Technology, 2019, 33 : 1357 - 1363
  • [44] Effect of processing conditions on shrinkage in injection molding
    Jansen, KMB
    Van Dijk, DJ
    Husselman, MH
    POLYMER ENGINEERING AND SCIENCE, 1998, 38 (05): : 838 - 846
  • [45] Injection Molding of Thermoplastic Cellulose Esters and Their Compatibility with Poly(Lactic Acid) and Polyethylene
    Willberg-Keyrilainen, Pia
    Orelma, Hannes
    Ropponen, Jarmo
    MATERIALS, 2018, 11 (12)
  • [46] Alternating multilayer structure of polyethylene/polypropylene blends obtained through injection molding
    Jiang, Kun
    Yu, Feilong
    Bai, Hongwei
    Gao, Jian
    Deng, Hua
    Zhang, Qin
    Fu, Qiang
    JOURNAL OF APPLIED POLYMER SCIENCE, 2012, 124 (06) : 4452 - 4456
  • [47] Morphology of polyethylene foamed crosslinked specimens made by hot mold injection molding
    Kotzev, G
    Touleshkov, N
    Christova, D
    Nedkov, E
    JOURNAL OF MACROMOLECULAR SCIENCE-PURE AND APPLIED CHEMISTRY, 1998, A35 (7-8): : 1127 - 1135
  • [48] Effect of the cascade injection molding on the filling behaviour
    Habrman M.
    Ráž K.
    Kalina T.
    Manufacturing Technology, 2019, 19 (06): : 936 - 940
  • [49] Investigation of cooling effect at corners in injection molding
    Kovacs, J. G.
    Siklo, B.
    INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER, 2011, 38 (10) : 1330 - 1334
  • [50] Effect of microstructures on the shrinkage of injection molding product
    Wu, Yue
    Gong, Yao
    Cha, Kyoung Je
    Park, Jang Min
    JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY, 2019, 33 (03) : 1357 - 1363
12345