Effect of Modifiers on Injection Molding of Waste Polyethylene Drip Tape

被引：0
|
作者：
Guo, Bin [1 ]
Wu, Shou-Jun [1 ]
Zhu, De-Lan [1 ]
机构：
[1] Northwest A&F Univ, Coll Water Resources & Architectural Engn, Yangling 712100, Shaanxi, Peoples R China
来源：
PROCEEDINGS OF THE 2015 INTERNATIONAL CONFERENCE ON MATERIAL SCIENCE AND APPLICATIONS (ICMSA 2015) | 2015年 / 3卷
关键词：
Polyethylene; Injection Molding; Ethylene-vinyl Acetate Copolymer; Dicumyl Peroxide; MECHANICAL-PROPERTIES; CROSS-LINKING; BLENDS;
D O I：
暂无
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
In this work, effects of Ethylene-vinyl acetate copolymer (EVA) and Dicumyl peroxide (DCP) on injection molding of recycled polyethylene (PE) materials obtained from a waste disposable drip tape are studied. Under injected at 175-230 degrees C and 35-40 MPa, the recycled PE materials with EVA showed good injection moldability, while those with DCP showed poor injection moldability with DCP introduction increasing. Under injected at 135-145 degrees C and 50-60 MPa, the recycled PE materials with DCP can be well injection molded.
引用
收藏
页码：948 / 951
页数：4
相关论文
共 50 条
  • [1] Investigation of polymer injection molding using calcareous waste concrete powder and polyethylene
    Kanda, Yasuyuki
    Kusumoto, Tsuguri
    POLYMER COMPOSITES, 2024,
  • [2] Simulation and optimization of injection molding for precise drip emitters
    Huazhong University of Science and Technology, China
    不详
    Nongye Jixie Xuebao, 2007, 4 (42-46):
  • [3] Effect of reprocessing pre-comsumer polyethylene in an injection molding environment
    Lewis, CL
    Buser, MA
    ANTEC'97 - PLASTICS SAVING PLANET EARTH, CONFERENCE PROCEEDINGS, VOLS 1 - 3, 1997, : 3162 - 3165
  • [4] Injection molding of carbonyl iron with polyethylene wax
    Lograsso, Barbara K.
    Bose, Animesh
    Carpenter, Burton J.
    Chung, Chan I.
    Hens, Karl F.
    Lee, Daeyong
    Lin, Shun-Tian
    Liu, Cui-Xia
    German, Randall M.
    Messler, Robert M.
    Murley, Paul F.
    Rhee, Byung O.
    Sierra, Carlos M.
    Warren, John
    International Journal of Powder Metallurgy (Princeton, New Jersey), 1989, 25 (04): : 337 - 348
  • [5] Injection blow molding technology for polyethylene terephthalate
    Bubeck, RA
    Barger, MA
    INTERNATIONAL POLYMER PROCESSING, 2000, 15 (04) : 337 - 342
  • [6] Ethylene copolymers as sintering enhancers and impact modifiers for rotational molding of polyethylene
    Chaudhary, BI
    Takács, E
    Vlachopoulos, J
    POLYMER ENGINEERING AND SCIENCE, 2002, 42 (06): : 1359 - 1369
  • [7] Effect of different managements with drip irrigation (tape)
    Najafabadi, Mazaher Amini
    Nafchi, Rouhallah Fatahi
    Salami, Hamidreza
    Vanani, Hamid Raeisi
    Ostad-Ali-Askari, Kaveh
    APPLIED WATER SCIENCE, 2023, 13 (02)
  • [8] Effect of different managements with drip irrigation (tape)
    Mazaher Amini Najafabadi
    Rouhallah Fatahi Nafchi
    Hamidreza Salami
    Hamid Raeisi Vanani
    Kaveh Ostad-Ali-Askari
    Applied Water Science, 2023, 13
  • [9] Injection Molding of Low-Density Polyethylene (LDPE) as a Model Polymer: Effect of Molding Parameters on the Microstructure and Crystallinity
    Leyva-Porras, Cesar
    Balderrama-Aguilar, Andrea
    Estrada-Avila, Yael
    Espelosin-Gomez, Inaki
    Mendoza-Duarte, Monica
    Pinon-Balderrama, Claudia
    Zenaida Saavedra-Leos, Maria
    Estrada-Moreno, Ivan
    POLYMERS, 2021, 13 (20)
  • [10] On the use of low-density polyethylene as disposable drip tape for field irrigation
    Zhu, Delan
    Wu, Shoujun
    Guo, Bin
    PLASTICS RUBBER AND COMPOSITES, 2018, 47 (03) : 133 - 137
12345