Rapid Synthesis of a Near-β Titanium Alloy by Blended Elemental Powder Metallurgy (BEPM) with Induction Sintering

被引：12
|
作者：
Jia, Mingtu [1 ]
Gabbitas, Brian [1 ]
机构：
[1] Univ Waikato, Waikato Ctr Adv Mat, Sch Engn, Hamilton 3240, New Zealand
来源：
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE | 2015年 / 46A卷 / 10期
关键词：
MECHANICAL-PROPERTIES; MICROSTRUCTURE EVOLUTION; HEAT-TREATMENT; DIFFUSION; INTERDIFFUSION; STRENGTH; BEHAVIOR;
D O I：
10.1007/s11661-015-3048-4
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
A near-beta Ti-13V-11Cr-3Al alloy was produced by blended elemental powder metallurgy combining warm compaction and induction sintering. Two Ti-13V-11Cr-3Al powder compacts with different oxygen content were manufactured by mixing PREP and HDH Ti powders with Cr and AlV master alloy powders, respectively. The effect of isothermal holding time, at a sintering temperature of 1573 K (1300 A degrees C), on pore characteristics and compositional homogeneity was investigated in this study. Pore coarsening by Ostwald ripening occurred with an increase in the isothermal holding time and Kirkendall voids were produced by a reaction between Ti and Cr. After an isothermal holding time of 10 minutes, the two sintered powder compacts had a homogeneous composition. Ti/AlV and Ti/Cr diffusion couples were used to predict the distribution of alloying elements, and the binary Ti-V, Ti-Al, and Ti-Cr interdiffusion coefficients were consistent with the distribution of alloying elements after isothermal holding. The mechanical properties of sintered powder compacts, prepared using PREP Ti powder as the raw powder, were optimized by sintered density and pore size.
引用
收藏
页码：4716 / 4729
页数：14
相关论文
共 50 条
  • [21] Synthesis of Ti/TiB Composites via Hydrogen-Assisted Blended Elemental Powder Metallurgy
    Song, Yuchao
    Dong, Shucheng
    Stasiuk, Oleksandr
    Savvakin, Dmytro
    Ivasishin, Orest
    FRONTIERS IN MATERIALS, 2020, 7
  • [22] Powder metallurgy processing of Nb-modified near β titanium alloys prepared with elemental powders
    Opini, Victor Carvalho
    Fogagnolo, Joao Batista
    Borras, Vicente Amigo
    Caram, Rubens
    Soyama, Juliano
    POWDER METALLURGY, 2023, 66 (05) : 530 - 536
  • [23] Optimization of Blended-Elemental Powder-Based Titanium Alloy Extrusions for Aerospace Applications
    El-Soudani, Sami M.
    Yu, Kuang-O
    Crist, Ernie M.
    Sun, Fusheng
    Campbell, Michael B.
    Esposito, Tony S.
    Phillips, Joshua J.
    Moxson, Vladimir
    Duz, Vlad A.
    METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2013, 44A (02): : 899 - 910
  • [24] Optimization of Blended-Elemental Powder-Based Titanium Alloy Extrusions for Aerospace Applications
    Sami M. El-Soudani
    Kuang-O. Yu
    Ernie M. Crist
    Fusheng Sun
    Michael B. Campbell
    Tony S. Esposito
    Joshua J. Phillips
    Vladimir Moxson
    Vlad A. Duz
    Metallurgical and Materials Transactions A, 2013, 44 : 899 - 910
  • [25] Microstructure and Properties of Ti80 Alloy Fabricated by Hydrogen-Assisted Blended Elemental Powder Metallurgy
    Wang, Baicheng
    Lei, Peng
    Ma, Guangyu
    Li, Dongdong
    Savvakin, Dmytro
    Ivasishin, Orest
    FRONTIERS IN MATERIALS, 2020, 7 (07):
  • [26] An Investigation into the Microstructural Response to Flexural Stresses of a Metastable β-Phase Ti Alloy produced by Blended Elemental Powder Metallurgy
    Naseri, Ryan
    Mitchell, David R. G.
    Gazder, Azdiar A.
    Niessen, Frank
    Nancarrow, Mitchell J. B.
    Savvakin, Dmytro G.
    Pereloma, Elena
    ADVANCED ENGINEERING MATERIALS, 2024, 26 (04)
  • [27] Synthesis, Characterization, and Surface Analysis of Near-β Ti20Nb20Zr Alloy Proceeded by Powder Metallurgy for Biomedical Applications
    M. A. Hussein
    JOM, 2022, 74 : 924 - 930
  • [28] Synthesis, Characterization, and Surface Analysis of Near-β Ti20Nb20Zr Alloy Proceeded by Powder Metallurgy for Biomedical Applications
    Hussein, M. A.
    JOM, 2022, 74 (03) : 924 - 930
  • [29] Blended elemental P/M synthesis of titanium alloys and titanium alloy-based particulate composites
    Hagiwara, Masuo
    Emura, Satoshi
    PROGRESS IN POWDER METALLURGY, PTS 1 AND 2, 2007, 534-536 : 777 - +
  • [30] Effect of Iron Content on Sintering Behavior of Ti-V-Fe-Al Near-β Titanium Alloy
    Dmytro G. Savvakin
    Andrew Carman
    Orest M. Ivasishin
    Mykhailo V. Matviychuk
    Azdiar A. Gazder
    Elena V. Pereloma
    Metallurgical and Materials Transactions A, 2012, 43 : 716 - 723
12345