Rapid Synthesis of a Near-β Titanium Alloy by Blended Elemental Powder Metallurgy (BEPM) with Induction Sintering

被引：12
|
作者：
Jia, Mingtu [1 ]
Gabbitas, Brian [1 ]
机构：
[1] Univ Waikato, Waikato Ctr Adv Mat, Sch Engn, Hamilton 3240, New Zealand
来源：
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE | 2015年 / 46A卷 / 10期
关键词：
MECHANICAL-PROPERTIES; MICROSTRUCTURE EVOLUTION; HEAT-TREATMENT; DIFFUSION; INTERDIFFUSION; STRENGTH; BEHAVIOR;
D O I：
10.1007/s11661-015-3048-4
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
A near-beta Ti-13V-11Cr-3Al alloy was produced by blended elemental powder metallurgy combining warm compaction and induction sintering. Two Ti-13V-11Cr-3Al powder compacts with different oxygen content were manufactured by mixing PREP and HDH Ti powders with Cr and AlV master alloy powders, respectively. The effect of isothermal holding time, at a sintering temperature of 1573 K (1300 A degrees C), on pore characteristics and compositional homogeneity was investigated in this study. Pore coarsening by Ostwald ripening occurred with an increase in the isothermal holding time and Kirkendall voids were produced by a reaction between Ti and Cr. After an isothermal holding time of 10 minutes, the two sintered powder compacts had a homogeneous composition. Ti/AlV and Ti/Cr diffusion couples were used to predict the distribution of alloying elements, and the binary Ti-V, Ti-Al, and Ti-Cr interdiffusion coefficients were consistent with the distribution of alloying elements after isothermal holding. The mechanical properties of sintered powder compacts, prepared using PREP Ti powder as the raw powder, were optimized by sintered density and pore size.
引用
收藏
页码：4716 / 4729
页数：14
相关论文
共 50 条
  • [1] Rapid Synthesis of a Near-β Titanium Alloy by Blended Elemental Powder Metallurgy (BEPM) with Induction Sintering
    Mingtu Jia
    Brian Gabbitas
    Metallurgical and Materials Transactions A, 2015, 46 : 4716 - 4729
  • [2] The effect of β-phase condition on the tensile behaviour in a near-β Ti alloy produced by blended elemental powder metallurgy
    Naseri, R.
    Mitchell, D. R. G.
    Savvakin, D. G.
    Nancarrow, M. J. B.
    Furuhara, T.
    Saleh, A. A.
    Gazder, A. A.
    Pereloma, E. V.
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2019, 747 : 232 - 243
  • [3] Effect of TiBp particle reinforcement on the creep resistance of near α titanium alloy made by blended elemental powder metallurgy
    Rhee, SI
    Nam, SW
    Hagiwara, M
    JOURNAL OF ALLOYS AND COMPOUNDS, 2003, 359 : 186 - 192
  • [4] BLENDED ELEMENTAL POWDER-METALLURGY OF TITANIUM-ALLOYS
    PARK, JS
    RO, DH
    TOAZ, MW
    AQUA, EN
    JOURNAL OF METALS, 1983, 35 (12): : 15 - 39
  • [5] Microstructure and properties of titanium alloy produced in the newly developed blended elemental powder metallurgy process
    Fujita, T
    Ogawa, A
    Ouchi, C
    Tajima, H
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 1996, 213 (1-2): : 148 - 153
  • [6] Enhancing Creep Resistance of Powder-Metallurgy Near-β Titanium Alloy via Rapid Heat Treatment Followed by Aging
    Qiu, Fucheng
    Cheng, Tuo
    Savvakin, Dmytro G.
    Ivasishin, Orest M.
    JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2024,
  • [7] A Comprehensive Study on Hot Deformation Behavior of the Metastable β Titanium Alloy Prepared by Blended Elemental Powder Metallurgy Approach
    Krystian Zyguła
    Oleksandr Lypchanskyi
    Aneta Łukaszek-Sołek
    Grzegorz Korpała
    Rafał Stanik
    Michał Kubiś
    Bartłomiej Przybyszewski
    Marek Wojtaszek
    Maik Gude
    Ulrich Prahl
    Metallurgical and Materials Transactions A, 2024, 55 : 933 - 954
  • [8] A Comprehensive Study on Hot Deformation Behavior of the Metastable β Titanium Alloy Prepared by Blended Elemental Powder Metallurgy Approach
    Zygula, Krystian
    Lypchanskyi, Oleksandr
    Lukaszek-Solek, Aneta
    Korpala, Grzegorz
    Stanik, Rafal
    Kubis, Michal
    Przybyszewski, Bartlomiej
    Wojtaszek, Marek
    Gude, Maik
    Prahl, Ulrich
    METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2024, 55 (03): : 933 - 954
  • [9] Achieving superior performance in powder-metallurgy near- β titanium alloy by combining hot rolling and rapid heat treatment followed by aging
    Qiu, Fucheng
    Cheng, Tuo
    Song, Yuchao
    Ivasishin, Orest M.
    Savvakin, Dmytro G.
    Ma, Guangyu
    Xu, Huiyan
    JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY, 2024, 171 : 24 - 36
  • [10] Mechanical behaviour of induction sintered blended elemental powder metallurgy Ti alloys
    Raynova, S.
    Yang, F.
    Bolzoni, L.
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2021, 799
12345