A new concept of hip joint stem and its fabrication using metastable TiNbSn alloy

被引：20

作者：

Jung, Taek-Kyun ^{[1
]}

Lee, Hyo-Soo ^{[1
]}

Semboshi, Satoshi ^{[2
]}

Masahashi, Naoya ^{[2
]}

Abumiya, Tadasu ^{[2
]}

Hanada, Shuji ^{[2
]}

机构：

[1] Korea Inst Ind Technol, Inchon 406840, South Korea

[2] Tohoku Univ, Inst Mat Res, Sendai, Miyagi 9808577, Japan

来源：

JOURNAL OF ALLOYS AND COMPOUNDS | 2012年 / 536卷

关键词：

TiNbSn alloys; Cold groove rolling; Cold swaging; Local heating; Young's modulus; Tensile strength; LOW YOUNGS MODULUS; MECHANICAL-PROPERTIES; TITANIUM-ALLOYS;

D O I：

10.1016/j.jallcom.2011.12.077

中图分类号：

O64 [物理化学（理论化学）、化学物理学];

学科分类号：

070304 ; 081704 ;

摘要：

Cold worked (Ti-35%Nb)-4%Sn alloy rods were locally heated to investigate the gradation of mechanical properties and develop an advanced Ti alloy stem for application as an artificial hip joint. Cold groove rolling was found to decrease Young's modulus, but subsequent cold swaging increased Young's modulus and tensile strength. Heating one edge of the cold worked rods resulted in the tensile strength and Young's modulus increasing significantly in the heated zone; the increase varied depending on the distance from the heated zone. The increase in tensile strength was attributed to the omega precipitation and the additional microstructure refinement by reverse transformation of alpha '' to beta. We could successfully fabricate an advanced hip joint stem with a tensile strength of 1.3 GPa in the proximal portion and Young's modulus of 43 GPa in the distal portion. (C) 2011 Elsevier B.V. All rights reserved.

引用

页码：S582 / S585

页数：4

共 50 条

[31] A new drive system using a shape memory alloy (SMA) heat engine and its applications
Kanada, T.
JOURNAL OF OPTOELECTRONICS AND ADVANCED MATERIALS, 2008, 10 (05): : 1061 - 1063
[32] Fabrication and characterization of a new high-strength alloy via WAAM using GMAW plus cold wire feeding
Ayan, Yusuf
MATERIALS CHEMISTRY AND PHYSICS, 2024, 328
[33] Bony abnormalities of the hip joint: a new comprehensive, reliable and radiation-free measurement method using magnetic resonance imaging
Harris-Hayes, Marcie
Commean, Paul K.
Patterson, Jacqueline D.
Clohisy, John C.
Hillen, Travis J.
JOURNAL OF HIP PRESERVATION SURGERY, 2014, 1 (02): : 62 - 70
[34] The Joint Clinic: Managing Excess Demand for Hip and Knee Osteoarthritis Referrals Using a New Physiotherapy-Led Outpatient Service
Gwynne-Jones, David P.
Hutton, Liam R.
Stout, Kirsten M.
Abbott, J. Haxby
JOURNAL OF ARTHROPLASTY, 2018, 33 (04): : 983 - 987
[35] Calculation of metastable free-energy diagrams and glass formation in the Mg-Cu-Y alloy and its boundary binaries using the Miedema model
de Tendler, R. Hojvat
Soriano, M. R.
Pepe, M. E.
Kovacs, J. A.
Vicente, E. E.
Alonso, J. A.
INTERMETALLICS, 2006, 14 (03) : 297 - 307
[36] GENERAL-ANALYSIS OF MAGNETIC REFRIGERATION AND ITS OPTIMIZATION USING A NEW CONCEPT - MAXIMIZATION OF REFRIGERANT CAPACITY
WOOD, ME
POTTER, WH
CRYOGENICS, 1985, 25 (12) : 667 - 683
[37] New Concept of Thin-Film Composite Nanofiltration Membrane Fabrication Using a Mist-Based Interfacial Polymerization Technique
Seah, Mei Qun
Khoo, Ying Siew
Lau, Woei Jye
Goh, Pei Sean
Ismail, Ahmad Fauzi
INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH, 2021, 60 (25) : 9167 - 9178
[38] RH PROBLEM IN OBSTETRICS AND A NEW CONCEPT OF ITS MANAGEMENT USING AMNIOCENTESIS AND SPECTROPHOTOMETRIC SCANNING OF AMNIOTIC FLUID
FREDA, VJ
AMERICAN JOURNAL OF OBSTETRICS AND GYNECOLOGY, 1965, 92 (03) : 341 - +
[39] A NEW PATTERNING PROCESS CONCEPT FOR LARGE-AREA TRANSISTOR-CIRCUIT FABRICATION WITHOUT USING AN OPTICAL MASK ALIGNER
MIKAMI, Y
NAGAE, Y
MORI, Y
KUWABARA, K
SAITO, T
HAYAMA, H
ASADA, H
AKIMOTO, Y
KOBAYASHI, M
OKAZAKI, S
ASAKA, K
MATSUI, H
NAKAMURA, K
KANEKO, E
IEEE TRANSACTIONS ON ELECTRON DEVICES, 1994, 41 (03) : 306 - 314
[40] Using a scale-bridging technique to determine the effect of elastic properties on stress distribution around the femoral stem of an artificial hip joint with a simplified geometry
C. U. Jeong
S. -C. Lee
H. N. Rhee
K. S. Park
S. -H. Choi
Metals and Materials International, 2014, 20 : 593 - 600

← 1 2 3 4 5 →