Structural and Mechanical Properties of Al/B4C Composites Fabricated by Wet Attrition Milling and Hot Extrusion

被引：39

作者：

Alizadeh, Morteza ^{[1
]}

Alizadeh, Mostafa ^{[2
]}

Amini, Rasool ^{[1
]}

机构：

[1] Shiraz Univ Technol, Dept Mat Sci & Engn, Shiraz 71555313, Iran

[2] Grad Univ Adv Technol, Dept Met, Inst Mat Sci & Engn, Kerman, Iran

来源：

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY | 2013年 / 29卷 / 08期

关键词：

Composites; Mechanical properties; Attrition milling; Hot extrusion; ALUMINUM-MATRIX COMPOSITES; TENSILE PROPERTIES; B4C; POWDERS; MICROSTRUCTURE; BEHAVIOR;

D O I：

10.1016/j.jmst.2013.04.015

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

In this study, Al matrix composites reinforced by 7.5 and 15 vol.% B4C particles and also monolithic Al (Al without the B4C particles) were produced by wet attrition milling and subsequent hot forward extrusion processes. The microstructure of the composites, evaluated by scanning electron microscopy (SEM), showed that the B4C particles were properly distributed in the Al matrix. Mechanical properties of the Al/B4C composites and monolithic Al were investigated by tensile, wear and hardness tests. The results revealed that with increasing content of B4C particles, the tensile strength and microhardness of composites increased but the elongation decreased. In addition, the tensile strength and microhardness of composite samples were higher than those of monolithic Al. The density measurements revealed that the density of composites decreased with increasing content of the B4C particles.

引用

页码：725 / 730

页数：6

共 50 条

[1] Structural and Mechanical Properties of Al/B4C Composites Fabricated by Wet Attrition Milling and Hot Extrusion
Morteza Alizadeh
Mostafa Alizadeh
Rasool Amini
Journal of Materials Science & Technology, 2013, 29 (08) : 725 - 730
[2] Mechanical properties and wear behavior of Al-2 wt.% Cu alloy composites reinforced by B4C nanoparticles and fabricated by mechanical milling and hot extrusion
Alizadeh, A.
Taheri-Nassaf, E.
MATERIALS CHARACTERIZATION, 2012, 67 : 119 - 128
[3] The effect of high B4C ratio on the improvement of mechanical properties and wear resistance of Al2024/B4C composites fabricated by mechanical milling-assisted hot pressing
Beder, Murat
CERAMICS INTERNATIONAL, 2025, 51 (07) : 9528 - 9547
[4] Wear Behavior of Nanostructured Al and Al–B4C Nanocomposites Produced by Mechanical Milling and Hot Extrusion
A. Alizadeh
E. Taheri-Nassaj
Tribology Letters, 2011, 44 : 59 - 66
[5] Effect of Milling and B4C Nanoparticles on the Mechanical Properties of Nanostructured Aluminum Composite Produced by Mechanical Milling and Hot Extrusion
Taheri-Nassaj, E.
Alizadeh, A.
MANUFACTURING SCIENCE AND TECHNOLOGY, PTS 1-8, 2012, 383-390 : 2733 - 2736
[6] Microtopography and mechanical properties of vacuum hot pressing Al/B4C composites
Zhang, Liu
Wang, Zhi
Li, Qinggang
Wu, Junyan
Shi, Guopu
Qi, Fangfang
Zhou, Xin
CERAMICS INTERNATIONAL, 2018, 44 (03) : 3048 - 3055
[7] Influence of B4C Particle Size on the Microstructure and Mechanical Properties of B4C/Al Composites Fabricated by Pressureless Infiltration
Liu, Yao
Peng, Haokai
Wei, Longjun
Peng, Hao
Ma, Donglin
Leng, Yongxiang
METALS, 2023, 13 (08)
[8] Phase transformation and mechanical properties of B4C/Al composites
Zhang L.
Shi G.
Xu K.
Hao W.
Li Q.
Junyan W.
Wang Z.
Wang, Zhi (wangzhi@ujn.edu.cn), 1600, Elsevier Editora Ltda (09): : 2116 - 2126
[9] Mechanical Properties and Corrosion Kinetics of B4C/Al Composites
Zhang, Liu
Wang, Xiao
Dong, Mengqi
Qian, Qinghua
Yang, Zirun
JOM, 2025,
[10] Phase transformation and mechanical properties of B4C/Al composites
Zhang, Liu
Shi, Guopu
Kun, Xu
Wu, Hao
Li, Qinggang
Wu, Junyan
Wang, Zhi
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2020, 9 (02): : 2116 - 2126

← 1 2 3 4 5 →