Comparison Studies of Electrical Discharge Machining (EDM) Process Model for Low Gap Current

被引：13
|
作者：
Yahya, Azli [1 ]
Andromeda, Trias [1 ]
Minhat, Ade Erawan [1 ]
Khamis, Nor Hisham [1 ]
Kalil, Kamal [1 ]
Rahim, Muhammad Arif Abdul [1 ]
机构：
[1] Fac Elect Engn, Skudai, Johor, Malaysia
来源：
MATERIALS SCIENCE AND INFORMATION TECHNOLOGY, PTS 1-8 | 2012年 / 433-440卷
关键词：
Electrical Discharge Machining; Dimensional Analysis; Artificial Neural Network; MRR; FUZZY-LOGIC; OPTIMIZATION;
D O I：
10.4028/www.scientific.net/AMR.433-440.650
中图分类号：
TP39 [计算机的应用];
学科分类号：
081203 ; 0835 ;
摘要：
This paper aims to compare the material removal rate, (v) over dot between a Dimensional Analysis (DA) model, an Artificial Neural Network (ANN) model and an experimental result for a low gap current of an Electrical Discharge Machining (EDM) process. The data analysis is based on a copper electrode and steel workpiece materials. The DA and ANN model that have been developed and reported earlier by authors are used to compare the material removal of EDM process. The result indicated that the ANN model provides better accuracy towards the experimental results.
引用
收藏
页码：650 / 654
页数：5
相关论文
共 50 条
  • [1] Analysis and Control of Electrical Discharge Machining (EDM) Process
    Zhou, Ming
    Han, Fuzhu
    Meng, Xianyi
    Chen, Baojiang
    2009 IEEE INTERNATIONAL CONFERENCE ON INDUSTRIAL ENGINEERING AND ENGINEERING MANAGEMENT, VOLS 1-4, 2009, : 164 - 168
  • [2] A review on current research trends in electrical discharge machining (EDM)
    Abbas, Norliana Mohd
    Solomon, Darius G.
    Bahari, Md. Fuad
    INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2007, 47 (7-8): : 1214 - 1228
  • [3] Modern process energy sources for electrical discharge machining (EDM)
    Läuter, M
    Schulze, HP
    Wollenberg, G
    COMPUTER-AIDED PRODUCTION ENGINEERING, 2003, : 339 - 348
  • [4] Erosion Rate Model Comparison of Electrical Discharge Machining Process
    Yahya, Azli
    Andromeda, Trias
    Rahim, Muhammad Arif Abdul
    Baharom, Ameruddin
    2012 4TH INTERNATIONAL CONFERENCE ON INTELLIGENT AND ADVANCED SYSTEMS (ICIAS), VOLS 1-2, 2012, : 122 - 125
  • [5] Study of workpiece thermal profile in Electrical Discharge Machining (EDM) process
    Moarrefzadeh, Ali
    WSEAS Transactions on Applied and Theoretical Mechanics, 2012, 7 (02): : 83 - 92
  • [6] Investigation and Optimization of Process Parameters in Electrical Discharge Machining (EDM) Process for NiTi 60
    Gaikwad, Mahendra U.
    Krishnamoorthy, A.
    Jatti, Vijaykumar S.
    MATERIALS RESEARCH EXPRESS, 2019, 6 (06):
  • [7] Fast and stable electrical discharge machining (EDM)
    Wu, Jianyang
    Zhou, Ming
    Xu, Xiaoyi
    Yang, Jianwei
    Zeng, Xiangwei
    Xu, Donghui
    MECHANICAL SYSTEMS AND SIGNAL PROCESSING, 2016, 72-73 : 420 - 431
  • [8] State of the art electrical discharge machining (EDM)
    Ho, KH
    Newman, ST
    INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2003, 43 (13): : 1287 - 1300
  • [9] Model of Pulse Power Generator in Electrical Discharge Machining (EDM) System
    Ade Erawan, Minhat
    Azli, Yahya
    Nor Hisham, Khamis
    Ahmad Saudi, Samosir
    Muhammad Arif, Abdul Rahim
    Trias, Andromeda
    Kartiko, Nugroho
    MECHANICAL AND MATERIALS ENGINEERING, 2014, 554 : 613 - +
  • [10] Analysis of Aerosol Emission and Hazard Evaluation of Electrical Discharge Machining (EDM) Process
    Jose, Mathew
    Sivapirakasam, S. P.
    Surianarayanan, M.
    INDUSTRIAL HEALTH, 2010, 48 (04) : 478 - 486
12345