Multicomponent materials from machining chips compacted by equal-channel angular pressing

被引：10
|
作者：
Lapovok, Rimma [1 ]
Qi, Yuanshen [1 ]
Ng, Hoi Pang [1 ]
Maier, Verena [2 ,3 ]
Estrin, Yuri [1 ,4 ]
机构：
[1] Monash Univ, Dept Mat Engn, Ctr Adv Hybrid Mat, Clayton, Vic 3168, Australia
[2] Univ Erlangen Nurnberg, Dept Mat Sci, Inst Gen Mat Properties 1, D-91058 Erlangen, Germany
[3] Univ Min & Met Leoben, Dept Mat Phys, A-8700 Leoben, Austria
[4] Moscow Inst Steel & Alloys, Lab Hybrid Nanomat, Moscow 119049, Russia
来源：
JOURNAL OF MATERIALS SCIENCE | 2014年 / 49卷 / 03期
关键词：
MECHANICAL-PROPERTIES; AL; DEFORMATION; PRESSURE; ALLOYS; MICROSTRUCTURE; CONSOLIDATION; EXTRUSION; ULTRAFINE; TITANIUM;
D O I：
10.1007/s10853-013-7801-z
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
Al and Mg machining chip blends were compacted by equal-channel angular pressing with back pressure. By varying the weight fraction of the constituent materials, temperature and processing route, as well as employing subsequent heat treatment, the microstructure and the mechanical properties of the compact were varied. The width of the interdiffusion zone and the formation of intermetallic phases near the interfaces between the two metals were studied by energy-dispersive X-ray spectroscopy and nanoindentation. It was shown that substantial improvement of mechanical properties, such as an increase of strength, strain-hardening capability and ductility, can be obtained. This is achieved by changing the processing parameters of equal-channel angular pressing and the annealing temperature, as well as by optimising the weight fraction of the constituent metals.
引用
收藏
页码：1193 / 1204
页数：12
相关论文
共 50 条
  • [21] Obtaining a Nanostructure in Titanium by Equal-Channel Angular Pressing
    G. I. Raab
    R. Z. Valiev
    Metal Science and Heat Treatment, 2000, 42 (9) : 361 - 365
  • [22] Significance of adiabatic heating in equal-channel angular pressing
    Yamaguchi, D
    Horita, Z
    Nemoto, M
    Langdon, TG
    SCRIPTA MATERIALIA, 1999, 41 (08) : 791 - 796
  • [23] Estimating the equivalent strain in equal-channel angular pressing
    Aida, T
    Matsuki, K
    Horita, Z
    Langdon, TG
    SCRIPTA MATERIALIA, 2001, 44 (04) : 575 - 579
  • [24] Influence of pressing speed on microstructural development in equal-channel angular pressing
    Patrick B. Berbon
    Minoru Furukawa
    Zenji Horita
    Minoru Nemoto
    Terence G. Langdon
    Metallurgical and Materials Transactions A, 1999, 30 : 1989 - 1997
  • [25] Influence of pressing speed on microstructural development in equal-channel angular pressing
    Berbon, PB
    Furukawa, M
    Horita, Z
    Nemoto, M
    Langdon, TG
    METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 1999, 30 (08): : 1989 - 1997
  • [26] Influence of pressing temperature on microstructural development in equal-channel angular pressing
    Yamashita, A
    Yamaguchi, D
    Horita, Z
    Langdon, TG
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2000, 287 (01): : 100 - 106
  • [27] Producing bulk nanocrystalline materials by combined hydrostatic extrusion and equal-channel angular pressing
    Kulczyk, M.
    Pachla, W.
    Mazur, A.
    Sus-Ryszkowska, M.
    Krasilnikov, N.
    Kurzydlowski, K. J.
    MATERIALS SCIENCE-POLAND, 2007, 25 (04): : 991 - 999
  • [28] Principle of equal-channel angular pressing for the processing of ultra-fine grained materials
    Kyushu Univ, Fukuoka, Japan
    Scripta Mater, 2 (143-146):
  • [29] Principle of equal-channel angular pressing for the processing of ultra-fine grained materials
    Iwahashi, Y
    Wang, JT
    Horita, Z
    Nemoto, M
    Langdon, TG
    SCRIPTA MATERIALIA, 1996, 35 (02) : 143 - 146
  • [30] Formation of inhomogeneous texture and structure in metal materials under equal-channel angular pressing
    Isaenkova, M
    Perlovich, Y
    Fesenko, V
    Grekhov, M
    Alexandrov, I
    Beyerlein, IJ
    ICOTOM 14: TEXTURES OF MATERIALS, PTS 1AND 2, 2005, 495-497 : 827 - 832
12345