Component Analysis of Adiabatic Shear Band Formed in High Speed Cutting of High Strength Alloy Steel

被引：1

作者：

Duan, C. Z. ^{[1
]}

Wang, Z. X. ^{[1
]}

Wang, M. J. ^{[1
]}

Kong, W. S. ^{[1
]}

机构：

[1] Dalian Univ Technol, Sch Mech Engn, Dalian 116024, Peoples R China

来源：

ADVANCES IN MECHANICAL ENGINEERING, PTS 1-3 | 2011年 / 52-54卷

关键词：

High speed cutting; Adiabatic shear band; Component analysis;

D O I：

10.4028/www.scientific.net/AMM.52-54.1482

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

The component distribution of adiabatic shear banding during high speed cutting(HSC) is important to understand the phase transformation during formation of adiabatic shear band and mechanism of serrated chip formation. This paper analyzed element distribution inside and near the adiabatic shear bands formed during HSC of 30CrNi(3)MoV high strength steel using electronic probe. It was found that there is no obvious element segregation, but carbon element tends to gather towards adiabatic shear band's boundaries. The density of carbon inside the shear bands tends to increase with the increase of cutting speed. The results indicated that the diffusion and gather of carbon may occur during formation of adiabatic shear band. The diffusion mechanism may be short-range diffusion driven by high-speed deformation and high temperature rise.

引用

页码：1482 / 1485

页数：4

共 50 条

[41] Adiabatic shear fracture prediction in high-speed cutting at various negative rake angles and feeds
Gu, Li-Yao
Wang, Min-Jie
ADVANCES IN MANUFACTURING, 2018, 6 (01): : 41 - 51
[42] Adiabatic shear fracture prediction in high-speed cutting at various negative rake angles and feeds
Li-Yao Gu
Min-Jie Wang
Advances in Manufacturing, 2018, 6 : 41 - 51
[43] Study on microscopic characteristics of adiabatic shear bands in the serrated chips formed during high speed machining
Duan, Chun-Zheng
Wang, Min-Jie
Li, Guo-He
Cai, Yu-Jun
Baozha Yu Chongji/Explosion and Shock Waves, 2007, 27 (01): : 91 - 96
[44] Unveiling the initiation and evolution mechanisms of adiabatic shear band in extruded 7003 aluminum alloy under high-speed impact load
Xing, Rui
Guo, Pengcheng
Xu, Congchang
Wang, Decheng
Li, Luoxing
JOURNAL OF ALLOYS AND COMPOUNDS, 2024, 983
[45] FE analysis of the effects of cutting speed on thermomechanical responses of AISI 4142 steel in high speed cutting
Gao, C. Y.
Fang, B.
MANUFACTURING SCIENCE AND ENGINEERING, PTS 1-5, 2010, 97-101 : 3183 - 3186
[46] Modeling periodic adiabatic shear band evolution during high speed machining Ti-6Al-4V alloy
Ye, G. G.
Xue, S. F.
Jiang, M. Q.
Tong, X. H.
Dai, L. H.
INTERNATIONAL JOURNAL OF PLASTICITY, 2013, 40 : 39 - 55
[47] Research on Adiabatic Shear during Serrated Chip Formation of High Speed Turning of Hardened Steel
Duan Chunzheng
Yu Haiyang
Wang Minjie
Yan Bing
Cai Yujun
MANUFACTURING ENGINEERING AND AUTOMATION I, PTS 1-3, 2011, 139-141 : 743 - +
[48] The influences of adiabatic shear evolution on tool failure in high-speed machining of railway steel
Gu, Liyao
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE, 2019, 233 (05) : 1588 - 1593
[49] HIGH-SPEED CUTTING STEEL PROPERTIES
ZMIHORSK.E
LACHOWSK.K
JANIAK, B
MECHANIK MIESIECZNIK NAUKOWO-TECHNICZNY, 1970, 43 (10): : 576 - &
[50] Effect of adiabatic shear bands in the ultra-high strength steel target on penetration resistance
Yin, Zhi-Xin
Ma, Chang-Xiang
Li, Shou-Xin
Liu, Yan-Lin
Dongbei Daxue Xuebao/Journal of Northeastern University, 2002, 23 (10): : 956 - 959

← 1 2 3 4 5 →