Component Analysis of Adiabatic Shear Band Formed in High Speed Cutting of High Strength Alloy Steel

被引：1
|
作者：
Duan, C. Z. [1 ]
Wang, Z. X. [1 ]
Wang, M. J. [1 ]
Kong, W. S. [1 ]
机构：
[1] Dalian Univ Technol, Sch Mech Engn, Dalian 116024, Peoples R China
来源：
ADVANCES IN MECHANICAL ENGINEERING, PTS 1-3 | 2011年 / 52-54卷
关键词：
High speed cutting; Adiabatic shear band; Component analysis;
D O I：
10.4028/www.scientific.net/AMM.52-54.1482
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
The component distribution of adiabatic shear banding during high speed cutting(HSC) is important to understand the phase transformation during formation of adiabatic shear band and mechanism of serrated chip formation. This paper analyzed element distribution inside and near the adiabatic shear bands formed during HSC of 30CrNi(3)MoV high strength steel using electronic probe. It was found that there is no obvious element segregation, but carbon element tends to gather towards adiabatic shear band's boundaries. The density of carbon inside the shear bands tends to increase with the increase of cutting speed. The results indicated that the diffusion and gather of carbon may occur during formation of adiabatic shear band. The diffusion mechanism may be short-range diffusion driven by high-speed deformation and high temperature rise.
引用
收藏
页码：1482 / 1485
页数：4
相关论文
共 50 条
  • [1] Strain evaluation model of adiabatic shear band produced by orthogonal cutting in high strength low alloy steel
    Li, Q
    Ma, C
    Lai, Z
    MATERIALS SCIENCE AND TECHNOLOGY, 1996, 12 (04) : 351 - 354
  • [2] Adiabatic Shear Localization in High Speed Cutting of Hardened Steel
    Duan, Chunzheng
    Kong, Weisen
    Wang, Zhaoxi
    Wang, Minjie
    RECENT TRENDS IN MATERIALS AND MECHANICAL ENGINEERING MATERIALS, MECHATRONICS AND AUTOMATION, PTS 1-3, 2011, 55-57 : 983 - 987
  • [3] Microstructure and hardness of adiabatic shear bands formed during orthogonal cutting of high strength steel
    Duan, Chun-Zheng
    Wang, Min-Jie
    Cailiao Kexue yu Gongyi/Material Science and Technology, 2004, 12 (06): : 602 - 605
  • [4] Periodic structure in adiabatic shear band formed by high speed impact upon steel 30MnCrNiMoB
    Li, Qiang
    Ma, Changxiang
    Lai, Zuhan
    Dongbei Daxue Xuebao/Journal of Northeastern University, 1995, 16 (04):
  • [5] High speed impact cutting (HSIC) of advanced high strength steel 42SiCr under exploitation of adiabatic shear bands
    Birnbaum, P.
    Kunke, A.
    Kraeusel, V.
    43RD INTERNATIONAL DEEP DRAWING RESEARCH GROUP, IDDRG CONFERENCE, 2024, 2024, 1307
  • [6] Microstructure of adiabatic shear bands induced during high speed machining of high-strength steel
    Duan, C. Z.
    Wang, M. J.
    Pang, J. Z.
    Cai, Y. J.
    CURRENT DEVELOPMENT IN ABRASIVE TECHNOLOGY, PROCEEDINGS, 2006, : 453 - +
  • [7] Adiabatic shear critical condition in the high-speed cutting
    Li Guohe
    Wang Minjie
    Duan Chunzheng
    JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2009, 209 (03) : 1362 - 1367
  • [8] Study on Chip Morphology and Adiabatic Shear in High Speed Cutting of Alloy Steels with Different Hardness
    Duan, Chunzheng
    Li, Honghua
    Wang, Minjie
    Cai, Yujun
    ADVANCED MECHANICAL ENGINEERING, PTS 1 AND 2, 2010, 26-28 : 875 - +
  • [9] Some metallurgical aspects of chips formed in high speed machining of high strength low alloy steel
    Duan, CZ
    Wang, MJ
    SCRIPTA MATERIALIA, 2005, 52 (10) : 1001 - 1004
  • [10] Effect of heat treatment on adiabatic shear bands in a high-strength low alloy steel
    Odeshi, AG
    Bassim, MN
    Al-Ameeri, S
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2006, 419 (1-2): : 69 - 75
12345