Self-tuning control of a nonlinear model of combustion instabilities

被引:40
|
作者
Krstic, M [1 ]
Krupadanam, A
Jacobson, C
机构
[1] Univ Calif San Diego, Dept Appl Mech & Engn Sci, La Jolla, CA 92093 USA
[2] MIT, Dept Mech Engn, Cambridge, MA 02139 USA
[3] United Technol Res Ctr, E Hartford, CT 06108 USA
基金
美国国家科学基金会;
关键词
adaptive control; averaging; combustion control; Galerkin approximation; nonlinear acoustics;
D O I
10.1109/87.772158
中图分类号
TP [自动化技术、计算机技术];
学科分类号
0812 ;
摘要
We present a self-tuning scheme for adapting the parameters of a proportional integral (PI) controller proposed by Fung and Yang for stabilization of a Culick-type! model of nonlinear acoustic oscillations in combustion chambers, Our adaptation criterion is Lyapunov-based and its objective is the regulation of nonlinear pressure oscillations to zero. We focus on a two-mode model and first develop a design based on an assumption that the amplitudes of the two modes are available for measurement. The adaptation mechanism is designed to stabilize both modes and prevent the phenomenon observed bg Candel and coworkers whose adaptive controller stabilizes the first but (under some conditions) apparently destabilizes the second mode, We also prove that the adaptation mechanism is robust to a time delay inherent to the actuation approach via heat release. In order to avoid requirements for sophisticated sensing of the mode amplitudes needed for feedback, we also develop an adaptation scheme which employs only one pressure sensor. In order for the adaptation scheme to be implementable, it is also necessary to know the control input matrix: of the system, Rather than performing a linear ID procedure with input excitation, we propose a simple nonlinear ID approach based on limit cycles (internal excitation) which exploits the quadratic character of the nonlinearities, Simulations illustrate the scheme's capability to attenuate limit cycles and its robustness to magnitude- and rate-saturation of the actuator.
引用
下载
收藏
页码:424 / 436
页数:13
相关论文
共 50 条
  • [31] Self-tuning nonlinear generalized predictive speed control of ultrasonic motors
    Shi, J. (shijz@mail.Haust.edu.cn), 1600, Chinese Society of Electrical Engineering, Qinghe, Beijing, 100085, China (32):
  • [32] NONLINEAR PIEZO-ACTUATOR CONTROL BY LEARNING SELF-TUNING REGULATOR
    LI, CJ
    BEIGI, HSM
    LI, SY
    LIANG, JC
    JOURNAL OF DYNAMIC SYSTEMS MEASUREMENT AND CONTROL-TRANSACTIONS OF THE ASME, 1993, 115 (04): : 720 - 723
  • [33] Sliding mode control with self-tuning law for uncertain nonlinear systems
    Kuo, Tzu-Chun
    Huang, Ying-Jeh
    Chang, Shin-Hung
    ISA TRANSACTIONS, 2008, 47 (02) : 171 - 178
  • [34] COMPARISON OF SELF-TUNING AND PREDICTIVE CONTROL ALGORITHMS APPLIED TO A NONLINEAR PROCESS
    COELHO, AAR
    GOMES, FJ
    AMARAL, WC
    YAMAKAMI, A
    PROCEEDINGS OF THE 28TH IEEE CONFERENCE ON DECISION AND CONTROL, VOLS 1-3, 1989, : 1058 - 1059
  • [35] Economic model predictive control with self-tuning terminal weight
    Mueller, Matthias A.
    Angeli, David
    Allgoewer, Frank
    2013 EUROPEAN CONTROL CONFERENCE (ECC), 2013, : 2044 - 2049
  • [36] A New Self-Tuning Nonlinear Model Predictive Controller for Autonomous Vehicles
    Abdolahi, Yasin
    Yousefi, Sajad
    Tavoosi, Jafar
    COMPLEXITY, 2023, 2023
  • [37] MULTIVARIABLE SELF-TUNING CONTROL - A MODEL-FOLLOWING APPROACH
    BITTANTI, S
    SCATTOLINI, R
    INTERNATIONAL JOURNAL OF CONTROL, 1985, 42 (05) : 1035 - 1047
  • [38] PID self-tuning controller based on internal model control
    Saegusa, T
    PROCEEDINGS OF THE 4TH INTERNATIONAL SYMPOSIUM ON HEATING, VENTILATING AND AIR CONDITIONING, VOLS 1 AND 2, 2003, : 1094 - 1099
  • [39] Self-tuning model predictive control for signalized traffic junctions
    Zammit, Luana Chetcuti
    Fabri, Simon G.
    Scerri, Kenneth
    2021 EUROPEAN CONTROL CONFERENCE (ECC), 2021, : 2585 - 2590
  • [40] Economic model predictive control with self-tuning terminal cost
    Mueller, Matthias A.
    Angeli, David
    Allgoewer, Frank
    EUROPEAN JOURNAL OF CONTROL, 2013, 19 (05) : 408 - 416