Development of high strength ductile hypereutectoid steel by cyclic heat treatment process

被引:39
|
作者
Saha, Atanu [2 ,3 ]
Mondal, Dipak Kumar [1 ]
Biswas, Koushik [4 ]
Maity, Joydeep [1 ]
机构
[1] Natl Inst Technol Durgapur, Dept Met & Mat Engn, Durgapur 713209, W Bengal, India
[2] CSIR Cent Mech Engn Res Inst, NDT, Durgapur 713209, W Bengal, India
[3] CSIR Cent Mech Engn Res Inst, Met Grp, Durgapur 713209, W Bengal, India
[4] Indian Inst Technol, Dept Met & Mat Engn, Kharagpur 721302, W Bengal, India
关键词
Hypereutectoid steel; Cyclic heat treatment; Lamellar faults; Fragmentation and thickening of cementite lamella; Divorced eutectoidal reaction; Cementite plates and spheroids; Strength and ductility; DISLOCATION INTERPHASE BOUNDARIES; TRANSFORMATION TEMPERATURE; MECHANICAL-PROPERTIES; PEARLITIC STEELS; CARBON-STEELS; KINK MOTION; MICROSTRUCTURE; SPHEROIDIZATION; MIGRATION; AUSTENITE;
D O I
10.1016/j.msea.2012.02.026
中图分类号
TB3 [工程材料学];
学科分类号
0805 ; 080502 ;
摘要
In this work a homogenizing annealed 1.24 wt% carbon steel was subjected to cyclic heat treatment process that consisted of repeated short-duration (6 min) holding at 894 degrees C (above Acm temperature) followed by forced air cooling. During short-duration holding at 894 degrees C. fragmentation (owing to partial dissolution) and thickening of cementite lamella occurred at the preferred high energy sites of lamellar faults. These undissolved fragmented cementite acted as pre-existing nuclei promoting the divorced eutectoidal reaction (DET) during forced air cooling that generated non lamellar region (NLR) in the microstructure apart from the presence of lamellar pearlite region (LPR) and cementite network (CN). The CN was also fragmented with repeated holding and cooling cycles. Besides, new lamellar fault sites were generated during forced air cooling to promote lamellar fragmentation. Accordingly, as the number of heat treatment cycles increases, more uniformly dispersed finer cementite particles (pre-existing nuclei) in austenite matrix was obtained at 894 degrees C. Therefore, the proportion of NLR increased and the proportions of LPR and CN decreased with the progress of cyclic heat treatment. After 8 cycles of heat treatment the microstructure mostly consisted of a combination of spheroids (0.55 +/- 0.24 mu m in size) and non-spheroids (mainly the plate shaped particles of 0.22 +/- 0.10 mu m in size) of cementite in 1:5 proportion by area% dispersed in ferrite matrix. The generation of cementite plates occurred through the motion of transformation disconnections. This provided an excellent combination of strength (UTS = 1086 MPa) and ductility (%elongation = 13) in this 1.24 wt% C steel. The property obtained had similarity to what was reported for a thermo-mechanically processed steel of much higher carbon content (1.8 wt%) where the microstructure consisted of solely the cementite spheroids of 0.65 mu m average size dispersed in ferrite matrix. (C) 2012 Elsevier B.V. All rights reserved.
引用
收藏
页码:204 / 215
页数:12
相关论文
共 50 条
  • [12] Enhancement of ductility and strength in 410 stainless steel through cyclic heat treatment
    Samson, Manoj R.
    Harshavardhana, N.
    Nirmal, R.
    Ranjith, R.
    3RD INTERNATIONAL CONFERENCE ON ADVANCES IN MECHANICAL ENGINEERING (ICAME 2020), PTS 1-6, 2020, 912
  • [13] Effect of welding and heat treatment on strength of high-strength steel columns
    Jiang, Jin
    Zhang, J.
    Liu, J.
    Chiew, S. P.
    Lee, C. K.
    JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH, 2018, 151 : 238 - 252
  • [14] Casting and Heat Treatment of Thick Advanced High Strength Steel
    Daniel Diner
    International Journal of Metalcasting, 2015, 9 : 87 - 87
  • [15] CASTING AND HEAT TREATMENT OF THICK ADVANCED HIGH STRENGTH STEEL
    Diner, Daniel
    INTERNATIONAL JOURNAL OF METALCASTING, 2015, 9 (01) : 87 - 87
  • [16] EFFECTS OF TEMPER-EMBRITTLING HEAT-TREATMENT ON DUCTILE FAILURE IN HIGH-STRENGTH LOW-ALLOY STEEL
    KING, JE
    KNOTT, JF
    METAL SCIENCE, 1981, 15 (01): : 1 - 6
  • [17] Hypervelocity impact into a high strength and ductile steel alloy
    Lach, E.
    Anderson, C.
    Schirm, V.
    Koerber, G.
    INTERNATIONAL JOURNAL OF IMPACT ENGINEERING, 2008, 35 (12) : 1625 - 1630
  • [18] OBTAINING HIGH-STRENGTH AND DUCTILE CHARACTERISTICS OF BIPHASE STEEL BY DIFFERENTIATED TREATMENT.
    Malinov, L.S.
    Sokolov, B.K.
    Konop-Lyashko, V.I.
    Smirnov, L.V.
    Metal Science and Heat Treatment (English Translation of Metallovedenie i Termicheskaya Obrabotka Metallov), 1980, 22 (7-8): : 576 - 580
  • [19] STUDY ON ROLLING PROCESS AND HEAT TREATMENT OF HIGH STRENGTH SHIP PLATE STEEL EH40
    Liu, Chunquan
    Peng, Qichun
    Xue, Zhengliang
    METALLURGICAL & MATERIALS ENGINEERING, 2018, 24 (03) : 199 - 208
  • [20] Heat Treatment Process, Microstructure, and Mechanical Properties of Spring Steel with Ultra-High Strength and Toughness
    Shi, Fang
    Zheng, Jian
    Zhang, Jie
    Zhao, Yang
    Chen, Liqing
    METALS, 2024, 14 (02)