Modeling of air back pressure in die-casting dies

被引：10
|
作者：
Lee, WB [1 ]
Lu, HY [1 ]
机构：
[1] Hong Kong Polytech Univ, Dept Mfg Engn, Kowloon, Peoples R China
来源：
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY | 1999年 / 91卷 / 1-3期
关键词：
die-casting; air back pressure; Poiseuille flow;
D O I：
10.1016/S0924-0136(98)00418-X
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
In high-pressure die-casting, molten metal is injected into a die cavity at a high velocity. The metal entering into the cavity expels the air from the cavity through the vents. Air back pressure will be created when the volume of metal flow exceeds the volume of air escaping out of the die cavity. A new mathematical model is proposed for the calculation of the creation of the back pressure in a die cavity. Air discharge through vents is modeled by the Poiseuille flow. The differential equation of the time rate of change of the back pressure is derived. The creation of the back pressure is correlated with the configuration sizes of the vent, and computations are carried out for different configurations of the vent geometry. (C) 1999 Elsevier Science S.A. All rights reserved.
引用
收藏
页码：264 / 269
页数：6
相关论文
共 50 条
  • [41] Investigation of die for pressure die-casting of Mg-alloy
    Torkar, M.
    Godec, M.
    Lamut, M.
    ENGINEERING FAILURE ANALYSIS, 2009, 16 (01) : 176 - 181
  • [42] Effects of die-casting defects on the blister formation in high-pressure die-casting aluminum structural components
    Dybowski, Bartlomiej
    Kielbus, Andrzej
    Poloczek, Lukasz
    ENGINEERING FAILURE ANALYSIS, 2023, 150
  • [43] ANALYSIS OF A DIE-CASTING DIE
    HERMAN, EA
    DIE CASTING ENGINEER, 1986, 30 (05): : 44 - 47
  • [44] AN INVESTIGATION OF COOLING AND LUBRICATION OF DIE-CASTING DIES USING A WATER LUBRICANT SPRAY
    CHHABRA, S
    CHU, YL
    ALTAN, T
    DIE CASTING ENGINEER, 1993, 37 (01): : 24 - &
  • [45] RECENT IMPROVEMENTS IN H-13 STEELS FOR ALUMINUM DIE-CASTING DIES
    NICHOLS, HP
    DIE CASTING ENGINEER, 1985, 29 (04): : 64 - 65
  • [46] System for computer-aided cavity layout design for die-casting dies
    Kumar, V.
    Madan, J.
    Gupta, P.
    INTERNATIONAL JOURNAL OF PRODUCTION RESEARCH, 2012, 50 (18) : 5181 - 5194
  • [47] A STUDY OF EROSION IN DIE-CASTING DIES BY A MULTIPLE PIN ACCELERATED EROSION TEST
    SHIVPURI, R
    YU, M
    VENKATESAN, K
    CHU, YL
    JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 1995, 4 (02) : 145 - 153
  • [48] DESIGNING THE HARDENING PRACTICE FOR PREMIUM H13 DIE-CASTING DIES
    PETTERSSON, S
    SANDBERG, O
    JOHNSON, B
    HEAT TREATMENT OF METALS, 1993, 20 (02): : 49 - 54
  • [49] LOW-PRESSURE DIE-CASTING - FACT AND FICTION
    PLUME, AW
    DIE CASTING ENGINEER, 1983, 27 (03): : 34 - 37
  • [50] FLOW MODELING IN HIGH-PRESSURE DIE-CASTING PROCESSES USING SPH MODEL
    Hu, M. Y.
    Cai, J. J.
    Li, N.
    Yu, H. L.
    Zhang, Y.
    Sun, B.
    Sun, W. L.
    INTERNATIONAL JOURNAL OF METALCASTING, 2018, 12 (01) : 97 - 105
12345