Measurement of the average permeability of natural fibre mats in resin transfer moulding application

被引：6
|
作者：
Rouison, D
Couturier, M
Panthapulakkal, S
Sain, M
机构：
[1] Univ Toronto, Fac Forestry, Ctr Biocomposites & Biomat Proc, Toronto, ON M5S 3B3, Canada
[2] Univ New Brunswick, Dept Chem Engn, Fredericton, NB E3B 5A3, Canada
来源：
POLYMERS & POLYMER COMPOSITES | 2006年 / 14卷 / 03期
关键词：
D O I：
10.1177/096739110601400302
中图分类号：
TB3 [工程材料学];
学科分类号：
0805 ; 080502 ;
摘要：
The permeability of hemp fibre mats used in a resin transfer moulding process were computed from the measured mould filling time, using a simplified mathematical approach. This approach could be applied because of the simple geometry of the mould and because a certain number of assumptions were made The permeability values obtained were found to decrease with increasing fibre content. In addition the hemp fibre permeability was found to be an order of magnitude lower than the value for glass fibre at a fibre content of 19 vol%. This preliminary work shows the importance of studying the permeability of natural fibre systems in order to provide the data necessary for the proper design of industrial moulds.
引用
收藏
页码：229 / 238
页数：10
相关论文
共 50 条
  • [21] Effects of injection pressure in resin transfer moulding (RTM) of woven carbon fibre/epoxy composites
    Kaynak, C
    Kas, YO
    POLYMERS & POLYMER COMPOSITES, 2006, 14 (01): : 55 - 64
  • [22] Mechanical properties of microwave cured glass fibre epoxy composites prepared by resin transfer moulding
    Maenz, Stefan
    Muehlstaedt, Mike
    Jandt, Klaus D.
    Bossert, Joerg
    JOURNAL OF COMPOSITE MATERIALS, 2015, 49 (23) : 2839 - 2847
  • [23] Effective average permeability of multi-layer preforms in resin transfer molding
    Calado, VMA
    Advani, SG
    COMPOSITES SCIENCE AND TECHNOLOGY, 1996, 56 (05) : 519 - 531
  • [24] Permeability prediction for the meso-macro coupling in the simulation of the impregnation stage of Resin Transfer Moulding
    Verleye, B.
    Lomov, S. V.
    Long, A.
    Verpoest, I.
    Roose, D.
    COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING, 2010, 41 (01) : 29 - 35
  • [25] Permeability measurement of a circular braided preform for resin transfer molding
    Cho, YK
    Song, YS
    Kang, TJ
    Chung, K
    Youn, JR
    FIBERS AND POLYMERS, 2003, 4 (03) : 135 - 144
  • [26] Permeability measurement of a circular braided preform for resin transfer molding
    Yun Kyoung Cho
    Young Seok Song
    Tae Jin Kang
    Kwansoo Chung
    Jae Ryoun Youn
    Fibers and Polymers, 2003, 4 : 135 - 144
  • [27] Investigation into the effects of fabric architecture on the processing and properties of fibre reinforced composites produced by resin transfer moulding
    Univ of Plymouth, Plymouth, United Kingdom
    Compos Part A Appl Sci Manuf, 1-2 (19-27):
  • [28] Mechanical properties and micromechanical analysis of nonwoven kenaf fibre/epoxy composites produced by resin transfer moulding
    Andre, N. G.
    Ariawan, Dody
    Ishak, Z. A. Mohd
    JOURNAL OF COMPOSITE MATERIALS, 2017, 51 (13) : 1875 - 1885
  • [29] The use of low pressure compression in resin transfer moulding to enhance the fibre volume fraction of composite materials
    Department of Engineering, Fac. of Eng./Information Technology, Australian National University, Canberra, ACT 0200, Australia
    不详
    Adv. Compos. Lett., 6 (283-287):
  • [30] An investigation into the effects of fabric architecture on the processing and properties of fibre reinforced composites produced by resin transfer moulding
    Pearce, NRL
    Guild, FJ
    Summerscales, J
    COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING, 1998, 29 (1-2) : 19 - 27
12345