Dry sliding wear characteristics of in-situ TiBw/Ti6Al4V composites with different network parameters

被引：42

作者：

An, Qi ^{[2
]}

Huang, L. J. ^{[1
,2
]}

Bao, Yang ^{[2
]}

Zhang, Rui ^{[2
]}

Jiang, Shan ^{[2
]}

Geng, Lin ^{[1
,2
]}

Xiao, Miaomiao ^{[2
]}

机构：

[1] Harbin Inst Technol, State Key Lab Adv Welding & Joining, POB 433, Harbin 150001, Heilongjiang, Peoples R China

[2] Harbin Inst Technol, Key Lab Adv Struct Funct Integrat Mat & Green Mfg, Sch Mat Sci & Engn, POB 433, Harbin 150001, Heilongjiang, Peoples R China

来源：

TRIBOLOGY INTERNATIONAL | 2018年 / 121卷

基金：

中国国家自然科学基金; 国家重点研发计划;

关键词：

Titanium matrix composites (TMCs); Network structure; Dry sliding wear; Heat treatment; TITANIUM MATRIX COMPOSITES; MECHANICAL-PROPERTIES; HEAT-TREATMENT; MICROSTRUCTURE; COATINGS; BEHAVIOR; TI-6AL-4V; EVOLUTION; ALLOY; TI;

D O I：

10.1016/j.triboint.2018.01.053

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

Ceramics reinforced titanium matrix composites (TMCs) exhibited high specific strength especially with a special network architecture. This study investigated wear characteristics of the novel TMCs with different parameters, the results show that in-situ TiBw enhances hardness and resists abrasion effectively. Meanwhile, the mechanism varied from micro-cutting to brittle debonding with increasing TiBw content, and increasing network size caused the increase of COF and wear loss. Consequently, the composite with 8.5 vol.% TiBw and network size of 60 mu m exhibited the best wear properties. Moreover, the subsequent heat treatment further enhanced the abrasion resistance by transformed beta phase coexisted with network structure, which resulted in decrease of COF from 0.251 to 0.149 and reduced wear loss by 19.7%.

引用

页码：252 / 259

页数：8

共 50 条

[21] Dry sliding wear of in-situ synthesized Al-TiC composites
Kumar, Abhishek
Gautam, Rakesh K.
Tyagi, Rajnesh
PROCEEDINGS OF MALAYSIAN INTERNATIONAL TRIBOLOGY CONFERENCE 2015, 2015, : 100 - 101
[22] Wear Characteristic Evaluation of Electrical Discharge Machined Ti6Al4V Surfaces at Dry Sliding Conditions
Philip, Jibin T.
Kumar, Deepak
Mathew, Jose
Kuriachen, Basil
TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS, 2019, 72 (10) : 2839 - 2849
[23] The Effect of Aging Temperature and Aging Duration on the Dry Sliding Wear Behavior of Ti6Al4V Alloy
Aksöz S.
Science of Sintering, 2023, 55 (04) : 527 - 538
[24] Wear Characteristic Evaluation of Electrical Discharge Machined Ti6Al4V Surfaces at Dry Sliding Conditions
Jibin T. Philip
Deepak Kumar
Jose Mathew
Basil Kuriachen
Transactions of the Indian Institute of Metals, 2019, 72 : 2839 - 2849
[25] Effects of Ti5Si3 characteristics adjustment on microstructure and tensile properties of in-situ (Ti5Si3+TiBw)/Ti6Al4V composites with two-scale network architecture
Jiao, Y.
Huang, L. J.
An, Q.
Jiang, S.
Gao, Y. N.
Cui, X. P.
Geng, L.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2016, 673 : 595 - 605
[26] Cutting forces and tool wear in dry milling of Ti6Al4V
Chen, Yun
Li, Huaizhong
Wang, Jun
ADVANCES IN ABRASIVE TECHNOLOGY XV, 2012, 565 : 454 - 459
[27] Characteristics and wear performance of borided Ti6Al4V alloy
Atar, Erdem
Kayali, E. Sabri
Cimenoglu, Huseyin
Surface and Coatings Technology, 2008, 202 (19) : 4583 - 4590
[28] Effects of extrusion and heat treatment on the microstructure and tensile properties of in situ TiBw/Ti6Al4V composite with a network architecture
Huang, L. J.
Geng, L.
Wang, B.
Xu, H. Y.
Kaveendran, B.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING, 2012, 43 (03) : 486 - 491
[29] Measurement and analysis of tool wear and surface characteristics in micro turning of SLM Ti6Al4V and wrought Ti6Al4V
Airao, Jay
Kishore, Hreetabh
Nirala, Chandrakant K.
MEASUREMENT, 2023, 206
[30] SEM OBSERVATIONS OF THE SLIDING WEAR MECHANISM INDUCED ON TI6AL4V ALLOY
BORGHI, I
MARTINELLA, R
ULTRAMICROSCOPY, 1984, 12 (1-2) : 111 - 111

← 1 2 3 4 5 →