Improved mechanical and macro-microscopic characteristics of shotcrete by incorporating hybrid alkali-resistant glass fibers

被引:6
|
作者
Hu, Zhongjing [1 ]
Wang, Qingbiao [2 ,3 ]
Lv, Hao [1 ]
Li, Kesheng [4 ]
Zhang, Jinpeng [5 ]
Ma, Yiming [2 ]
机构
[1] Shandong Univ Sci & Technol, Coll Safety & Environm Engn, Coll Safety & Emergency Management, Qingdao 266590, Shandong, Peoples R China
[2] Shandong Univ Sci & Technol, Coll Resources, Tai An 271019, Shandong, Peoples R China
[3] Shandong Univ Sci & Technol, Natl Engn Lab Coalmine Backfilling Min, Tai An 271019, Shandong, Peoples R China
[4] China Univ Min & Technol, State Key Lab Intelligent Construct & Hlth Operat, Xuzhou 221116, Jiangsu, Peoples R China
[5] Shandong Agr Univ, Coll Water Conservancy & Civil Engn, Tai An 271018, Shandong, Peoples R China
关键词
Fiber reinforced shotcrete; Alkali-resistant glass fiber; Macro-micro properties; Strengthening mechanism of hybrid fiber; REINFORCED CONCRETE; POLYPROPYLENE FIBERS; BASALT FIBER; PERFORMANCE; STEEL; DURABILITY; STRENGTH; BEHAVIOR; TENSILE;
D O I
10.1016/j.conbuildmat.2023.133131
中图分类号
TU [建筑科学];
学科分类号
0813 ;
摘要
Fiber reinforced shotcrete (FRS) is an essential method for engineering support such as tunnels, slopes, and foundation pits. This study focuses on addressing the limitations of traditional fiber-reinforced shotcrete (FRS) by introducing innovative alkali-resistant glass fiber (AR-GF) series products, namely Anti-Crak & REG; HP (HP) and AntiCrak & REG; HD (HD) mixed FRS. The aim is to overcome issues such as rusting, corrosion, high labor, and low surface aesthetics. The mechanical and microscopic properties of alkali-resistant glass fiber reinforced shotcrete (ARGFRS) were investigated under different conditions of admixture and mixing patterns using uniaxial compression, split tensile, and scanning electron microscopy (SEM) tests. The results show that the mixing of AR-GF series products HD and HP greatly enhanced the mechanical properties of shotcrete and improved the microstructure of shotcrete. The split tensile strength was increased by 23% with the 6% content compared to 3% with HP fiber alone. AR-GFRS in HP and HD hybrid mode has better compressive and splitting tensile strength compared with the same total content of AR-GF with HP fibers alone. The optimal amount of HP was 3% of the cement mass for single mixing of HP, and the optimal mixing pattern of HP and HD was the mixing of HP (length 24 mm) and HD (length 18 mm and 6 mm). The excellent integrity of the rupture surface can be observed from a microscopic point of view, and the AR-GF was predominantly extracted. The HP damage morphology on the rupture surface was classified into fiber integrity, breakage, disorganization, and dispersion. A hybrid AR-GFRS model was established to reveal the hybrid AR-GF shotcrete reinforcement mechanism. The research results provide new ideas for the development of mixed fiber shotcrete, and lay the foundation for the design and construction of mixed alkali-resistant glass fiber shotcrete support.
引用
下载
收藏
页数:15
相关论文
共 40 条
  • [31] Effect of alkali-resistant glass fiber and silica fume on mechanical and shrinkage properties of cement-based mortars
    Chen, Haiming
    Wang, Pengju
    Pan, Jin
    Lawi, Abubakar S.
    Zhu, Yuntao
    CONSTRUCTION AND BUILDING MATERIALS, 2021, 307
  • [33] Mechanical properties of alkali-activated slag based SIFCON incorporating waste steel fibers and waste glass
    Gok, Saadet Gokce
    Sengul, Ozkan
    CONSTRUCTION AND BUILDING MATERIALS, 2023, 408
  • [34] Improved macro-microscopic characteristic of gypsum-slag based cementitious materials by incorporating red mud/carbide slag binary alkaline waste-derived activator
    Chang, Ning
    Li, Hui
    Liu, Wenhuan
    Zheng, Wukui
    Zhu, Huimei
    Wan, Zhenmin
    Wu, Xingzi
    Jiang, Hongjian
    Zhang, Lu
    CONSTRUCTION AND BUILDING MATERIALS, 2024, 428
  • [35] Mechanical Characteristics of Hybrid Composites with ±45° Glass and 0°/90° Stainless Steel Fibers
    O'Brien, Caitlin
    Zaghi, Arash E.
    MATERIALS, 2018, 11 (08)
  • [36] Experimental research on the mechanical properties of alkali-resistant glass fiber concrete acting as tunnel seismic isolation layer under periodic cyclic dynamic loading
    Zhang, Cong
    Wang, Qingbiao
    Zhang, Yonggang
    Wang, Shanyong
    Zhang, Xinru
    Wang, Yunxiao
    CASE STUDIES IN CONSTRUCTION MATERIALS, 2024, 21
  • [37] Structural laminated hybrid composites based on raffia and glass fibers: Effect of alkali treatment, mechanical and thermal properties
    Ouarhim, Wafa
    Essabir, Hamid
    Bensalah, Mohammed-Ouadi
    Zari, Nadia
    Bouhfid, Rachid
    el Kacem Qaiss, Abou
    COMPOSITES PART B-ENGINEERING, 2018, 154 : 128 - 137
  • [38] Effect of Fiber Content on Mechanical Properties and Microstructural Characteristics of Alkali Resistant Glass Fiber Reinforced Concrete
    Wu, Chao
    He, Xiongjun
    Zhao, Xia
    He, Li
    Song, Yuan
    Zhang, Xiuyan
    ADVANCES IN MATERIALS SCIENCE AND ENGINEERING, 2022, 2022
  • [39] Mechanical and Thermal Characteristics of Hybrid Composites Fortified with Flax, Banyan, and Glass Fibers for Automobile Safety Applications
    Baladivakar, S.
    Starvin, M. S.
    Raj, J. Bensam
    JOURNAL OF NATURAL FIBERS, 2022, 19 (17) : 15392 - 15403
  • [40] Effect of dispersion of alumina nanoparticles and graphene nanoplatelets on microstructural and mechanical characteristics of hybrid carbon/glass fibers reinforced polymer composite
    Abu-Okail, Mohamed
    Alsaleh, Naser A.
    Farouk, W. M.
    Elsheikh, Ammar
    Abu-Oqail, Ahmed
    Abdelraouf, Yasmin A.
    Ghafaar, M. Abdel
    JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2021, 14 : 2624 - 2637